Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 495

Страница: 495 / 564

RADIATOR AND COOLANT SYSTEM (DIESEL)

Radiator

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 15-5

7. Disconnect the two-pin connector between the fan motor and the wire harness

(Figure 15-4,

Page 15-5)

8. Remove the flanged locknuts and flanged bolts securing the two radiator support brackets to the chassis

and remove brackets.

9. Push the splash guard toward the dash and carefully lift the radiator straight up to remove from vehicle.

See following CAUTION.

CAUT ION

• To prevent damage to the radiator when lifting it out of the vehicle, avoid striking the

protruding hardware in upper front crossmember.

10. Remove the four bolts securing the fan shroud assembly to the radiator and remove the shroud.

RADIATOR INSTALLATION

1. Place fan shroud assembly on radiator and secure with four lock-patch bolts. Tighten the hardware to 48

in-lb (5 N·m).

2. Carefully lower the radiator straight down into chassis to rest in the aluminum frame channel.

See pre-

ceding CAUTION.

3. Install the two radiator support brackets over the studs of the rubber isolators and finger-tighten flanged

locknuts. Secure brackets to chassis with flanged bolts tightened to 132 in-lb (15 N·m). Tighten the
flanged locknuts to 84 in-lb (9.0 N·m).

4. Connect the two-pin connector from the fan motor to the wire harness.

5. Attach the upper and lower radiator hoses and secure with clamps.

6. Attach the hose to the radiator fill spout and secure with clamp.

7. Refill the cooling system.

See Engine Coolant Change on page 15-1.

Figure 15-4 Radiator Bracket Attachment

Radiator

Support

Bracket

Flanged

Bolts

Flanged

Nut

Two-Pin

Connector

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды