Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 446

Страница: 446 / 564

DIESEL ENGINE, MUFFLER, FUEL SYSTEM, AND CLUTCHES

Fuel System

Page 13c-16

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

13C

FUEL TANK
See General Warning, Section 1, Page 1-1.

WARNING

• If the fuel tank is damaged, replace it. Do not attempt to repair it. See the following tank

removal and disposal procedure.

CAUT ION

• Use only diesel grade no. 2 fuel with a cetane rating of 45 or higher for diesel engines.

Fuel Tank Removal

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-1.

3. Remove seat(s) and, if equipped, the center seat plate.

4. Remove the upper portion of the ROPS (Roll Over Protection Structure) frame.

See ROPS Removal,

Section 4, Page 4-7.

5. Remove the seat frame.

See Seat Support Removal, Section 4, Page 4-10.

6. Disconnect the fuel feed line (1) from the fuel tank to the primary fuel filter and raise the end of the hose

above the fuel tank. Plug the line

(Figure 13c-8, Page 13c-8)

See following NOTE and DANGER.

NOTE:

The fuel line contains diesel fuel. Squeeze the fuel line closed to prevent fuel flow after the fuel line
is removed. Plug or cap the fuel line.

DANGER

• Diesel fuel! Flammable! Explosive! Do not smoke. Keep sparks and flames away from the

vehicle and service area.

7. Disconnect the fuel return line (5) from the engine and raise the end of the hose above the fuel tank. Plug

the line.

See previous NOTE and DANGER.

8. Loosen the clamp and remove the vent tube from the fuel tank.

9. Remove the fuel tank cap.

10. Use a siphon with a built-in suction device to siphon all fuel from the tank and into an approved container.

See following DANGER and WARNING.

DANGER

• Diesel fuel! Flammable! Explosive! Do not smoke. Keep sparks and flames away from the

vehicle and service area.

WARNING

• Never attempt to siphon fuel with a hose that does not have a built-in suction device.
• Never attempt to siphon fuel with your mouth.

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды