Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 391 | Manualshive

Страница: 391 / 564

background image

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 13b-1

13B

SECTION 13B – HONDA GASOLINE ENGINE,
MUFFLER, FUEL SYSTEM, AND CLUTCHES

ý

DANGER

• See General Warning, Section 1, Page 1-1.

ý

WARNING

• See General Warning, Section 1, Page 1-1.

GASOLINE ENGINE

See General Warning, Section 1, Page 1-1.

This section contains information on removing and installing the Honda gasoline engine. For complete
instructions on engine disassembly, repair, rebuilding, and reassembly, refer to the engine manual.

See the

Honda GX620 engine manual (CCI P/N 102615401).

ENGINE REMOVAL
See General Warning, Section 1, Page 1-1.

CAUT ION

• Before removal and disassembly, clean the engine.

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally...” in General

Warning, Section 1, Page 1-2.

3. Remove the cargo bed.

See Cargo Bed Removal, Section 4, Page 4-12.

4. Remove the ROPS (Roll Over Protection Structure).

See ROPS Removal, Section 4, Page 4-7.

5. Remove the lower rear ROPS bars.

See ROPS Removal, Section 4, Page 4-7.

6. Remove the seat frame.

See Seat Support Removal, Section 4, Page 4-10.

7. Remove the engine cover plate.

See following NOTE.

NOTE:

The engine lift tab must be secured to the engine after the cover plate has been removed. Tighten
the bolt to 192 in-lb (22 N·m).

8. Remove the engine name plate.

See following NOTE.

NOTE:

Do not discard the name plate. New engines are not supplied with name plates that have fuel line
and accelerator cable provisions.

9. Close the shut-off valve on the fuel tank.

10. Remove the fuel line and in-line filter from the engine.

See following DANGER.

«
...
389
390
391
392
393
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

T-SPORT NEV 2014

Бренд: ACG Страницы: 85

Бренд: Cart-Tek Страницы: 18

Бренд: Cart-Tek Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды