Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 345

Страница: 345 / 564

ELECTRICAL COMPONENTS: DIESEL VEHICLES

Thermostat Switch

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 12c-17

12C

5. Lift the retaining tabs on the connector and remove the halogen bulb.

Headlight Bulb Installation

NOTE:

When handling halogen bulbs, do not touch the glass portion of bulb. Oil from finger tips can cause
premature failure of the bulb.

1. Attach the connector harness to the halogen bulb. The retaining tab should lock onto the halogen bulb

(Figure 12c-15, Page 12c-17)

2. From the front of vehicle, reach under the cowl and insert the bulb assembly into the headlight lens.

3. Turn the bulb assembly counterclockwise one-quarter turn.

4. Connect the battery cables, positive (+) cable first, and tighten the terminals to 144 in-lb (16 N·m). Coat

terminals with Battery Terminal Protector Spray (CCI P/N 1014305).

THERMOSTAT SWITCH

See General Warning, Section 1, Page 1-1.

Testing the Thermostat Switch

See Test Procedure 11, Section 11c, Page 11c-25.

Thermostat Switch Removal

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the two-pin connector between the thermostat switch and the wire harness

(Figure 12c-16,

Page 12c-18)

See following WARNING.

WARNING

• Hot! Coolant system is pressurized. Do not remove thermostat switch while engine is hot.

3. Loosen the radiator cap to relieve pressure.

Figure 12c-15 Headlight Bulb

Bulb

Headlight Lens

Connector

Harness

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды