manualshive.com logo in svg

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Клубный автомобиль IntelliTach XRT 1550 - это универсальный транспортный средство для гольфа и индустрии. Убедитесь, что ваш автомобиль всегда находится в отличном состоянии, загрузив бесплатное Руководство по обслуживанию и ремонту с manualshive.com. Проведите необходимую профилактику и обслуживание для долговечности вашего автомобиля.

Поделиться
Скачать
background image

KAWASAKI GASOLINE ENGINE, MUFFLER, FUEL SYSTEM, AND CLUTCHES

Fuel System

Page 13a-14

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

13A

CAUT ION

• Do not overtighten the screws. Overtightening the screws will strip the mounting holes in the

fuel tank.

6. Secure the orange wire (7) to the center post with the nut (9) previously removed 

(Figure 13a-6,

Page 13a-12)

. Tighten the hardware to 17 in-lb (1.9 N·m) and secure the rubber boot (8) to the center

post.

7. Install the passenger seat. 

See Seat Installation, Section 4, Page 4-9.

8. Connect the spark plug wires.

9. Connect the battery cables, positive (+) cable first, and tighten the hardware to 144 in-lb (16 N·m). Coat

terminals with Battery Terminal Protector Spray (CCI P/N 1014305).

FUEL TANK
See General Warning, Section 1, Page 1-1.

ý 

WARNING

• If the fuel tank is damaged, replace it. Do not attempt to repair it. See the following tank

removal and disposal procedure.

Fuel Tank Removal

1. Turn the key switch OFF and remove the key. Place the Forward/Reverse handle in NEUTRAL. Chock

the wheels.

2. Disconnect the battery cables as instructed. 

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-1.

3. Remove both seats.

4. Remove the center seat plate.

5. Remove the upper portion of the ROPS. 

See ROPS Removal, Section 4, Page 4-7.

6. Remove the bolts, washers and flanged locknuts from the seat frame, seat side plates, and engine cover

plate.

7. Turn the fuel shut-off valve to the closed (OFF) position 

(Figure 13a-11, Page 13a-17)

.

8. Run the engine until all fuel in the carburetor, fuel pump, and fuel lines is used and the engine stalls.

9. Loosen the clamp and disconnect the fuel line from the fuel tank shut-off valve 

(Figure 13a-9,

Page 13a-15)

.

10. Loosen the clamp and remove the vent tube from the fuel tank

.

11. Remove the fuel tank cap.

12. Use a siphon with a built-in suction device to siphon all fuel from the tank and into an approved container.

See following DANGER and WARNING.

ý 

DANGER

• Gasoline! Flammable! Explosive! Do not smoke. Keep sparks and flames away from the

vehicle and service area.

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Загрузить еще бренды