Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 355

Страница: 355 / 564

KAWASAKI GASOLINE ENGINE, MUFFLER, FUEL SYSTEM, AND CLUTCHES

Gasoline Engine

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

Page 13a-3

13A

11. Remove the choke cable.

See Choke Cable Removal on page 13a-20.

12. Remove the engine air inlet hose (4).

See Air Filter Outlet Hose Removal on page 13a-26.

13. Remove the accelerator cable.

See Accelerator Cable Removal on page 13a-18.

14. Remove the muffler.

See Muffler Removal on page 13a-6.

15. Remove the intermediate exhaust pipe.

See Intermediate Pipe Removal on page 13a-7.

16. Remove the clutch outer cover.

See Clutch Outer Cover Removal on page 13a-37.

17. Remove the clutches (5).

See Drive Clutch Removal on page 13a-29. Also See Driven Clutch

Removal on page 13a-34.

18. Remove the clutch inner cover (6).

See Clutch Inner Cover Removal on page 13a-37.

19. Remove the exhaust manifold (7).

20. Remove the electrical connectors:

20.1. Disconnect the engine harness from the chassis harness.

20.2. Disconnect all wires attached to the starter solenoid.

See following NOTE.

NOTE:

Mark or tape together, for identification, the connectors on the starter solenoid posts.

21. Drain the engine oil.

See Engine Oil and Filter Change, Section 10b, Page 10b-8.

22. Remove engine oil inlet and outlet hoses from the engine.

See Oil Filter Hose Removal on page 13a-5.

See also following NOTE.

NOTE:

Plug each line as it is removed from the engine. Without plugs, oil will leak from the lines.

23. Remove the engine mounting hardware (8)

(Figure 13a-1, Page 13a-2)

24. Lift the engine out by its lift tabs (9).

25. If a new engine will be installed, remove and retain the following:

•

Oil Filter Adapter (1)

(Figure 13a-2, Page 13a-4)

•

Engine Lift Tabs

•

Choke Cable Return Spring

ENGINE INSTALLATION

See General Warning, Section 1, Page 1-1.

1. Before a new engine is installed, the following components must be installed:

•

Oil Filter Adapter (1) (new o-rings (2) required)

(Figure 13a-2, Page 13a-4)

– Tighten the hardware to

33 ft-lb (44 N·m)

•

Engine Lift Tabs – Tighten the hardware to 21 ft-lb (28 N·m)

•

Choke Cable Return Spring

2. Lower the engine into the engine compartment and closely align the engine block mounting holes with

the holes in the engine plate (10)

(Figure 13a-1, Page 13a-2)

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды

Club Car IntelliTach XRT 1550, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание IntelliTach XRT 1550

Отзывы:

Похожие инструкции для IntelliTach XRT 1550

Бренды по названию

Популярные бренды