Club Car IntelliTach XRT 1550 Скачать руководство пользователя страница 380 | Manualshive

Страница: 380 / 564

background image

KAWASAKI GASOLINE ENGINE, MUFFLER, FUEL SYSTEM, AND CLUTCHES

Clutches

Page 13a-28

2007 Carryall 295/295 SE & XRT 1550/1550 SE Gasoline, Diesel and IntelliTach M & S Manual

13A

If the clutches are not operating properly, perform the following:

1. Check the governor and throttle settings.

See Engine RPM Adjustment on page 13a-22.

2. Inspect both clutches for dirt and debris buildup on component parts. Clean the exterior surfaces of both

clutches with water to remove any dust or dirt, then drive the vehicle and check for proper operation.

See

Drive Clutch on page 13a-29.

See also Driven Clutch on page 13a-34.

3. Check the clean clutches for wear.

4. If cleaning both clutches does not solve the problem, disassemble and thoroughly clean all parts in the

drive and driven clutches.

5. Check the drive clutch rollers and weights for wear.

See Drive Clutch Cleaning and Inspection on

page 13a-30.

DRIVE BELT
See General Warning, Section 1, Page 1-1.

The drive belt should be inspected periodically for wear and glazing. If it is excessively worn, frayed, or
glazed, replace the belt.

As the drive belt wears, the engine RPM will increase to compensate for the change in torque ratio. This RPM
increase helps maintain the correct maximum ground speed of 25 mph (40 km/h).

Drive Belt Removal

1. Turn the key switch OFF and remove the key. Set the park brake. Place the Forward/Reverse handle in

NEUTRAL.

2. Disconnect the battery cables as instructed.

See WARNING “To avoid unintentionally starting...” in

General Warning, Section 1, Page 1-2.

3. Disconnect the spark plug wires.

See WARNING “To avoid unintentionally starting...” in General

Warning, Section 1, Page 1-2.

4. Remove the outer clutch cover.

See Clutch Outer Cover Removal on page 13a-37.

5. Grasp the belt midway between the drive and driven clutches and squeeze the belt together as tightly as

possible

(Figure 13a-28, Page 13a-28)

.

6. Guide the belt over the driven clutch and roll the belt off the driven clutch by rotating the clutch clockwise.

See following CAUTION.

Figure 13a-28 Drive Belt Removal

«
...
378
379
380
381
382
...
»

Содержание IntelliTach XRT 1550





















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для IntelliTach XRT 1550

Бренд: Pride Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды