Messages
371
RIVAGE PM10 Operation Manual
Mixing data corrupt on Editor!
To recover, go to DEVICE SYNC screen
and re-sync data (EDITOR --> DSP).
The internal data of Editor is corrupt.
To recover the data, access the DEVICE SYNC screen, and then re-
sync data in the EDITOR
→
DSP sync direction.
Multiple word clock masters found!
Multiple DSP engines that are assigned as the word clock master
have been detected. Assign the word clock master to only one
unit in the system.
No Battery! (Console)
The internal battery of the console is exhausted. The internal
clock cannot keep the correct time. Please contact your Yamaha
dealer for information regarding battery replacement.
No Battery! (DSP Engine)
The DSP engine’s internal battery is exhausted. The internal clock
cannot keep the correct time. Please contact your Yamaha dealer
for information regarding battery replacement.
No scene to update. Store scene first.
The Update function is not available because there is no scene.
Store a scene first.
Offset values can be edited only when
OVERLAY is ON
You can set the Overlay offset values only when Overlay is turned
on.
Only one DCA can be rolled out at one
time.
You cannot roll-out DCA members on multiple bays
simultaneously.
Overlay turned off.
Overlay has been turned off.
Overlay turned on.
Overlay has been turned on.
Page bookmarked
The page is bookmarked.
Power loss to PSU detected (CS X)
One of the two power supply units failed to supply power. “X”
represents the power supply unit (A or B) for which power failure
was detected.
Same page is already open
The page cannot be displayed because the same page is already
open on another screen.
Saving aborted
The file save operation was interrupted.
Scene #XX already exists
The scene renumbering operation cannot be completed because
a scene number that already exists was specified.
Scene #XX is empty!
A scene you tried to recall does not exist.
Scene #XX is protected!
The scene is protected, and your operation (for example, delete)
cannot be completed.
Scene delete undone
The scene delete operation was undone.
Scene duplicate undone
The scene copy operation was undone.
Scene recall undone
The scene recall operation was undone.
Scene store undone
The scene store operation was undone.
Screen captured
A screen has been captured.
Software control for this card is disabled.
Check the card's DIP SW setting.
This card is not working properly. Check the card's
DIP switch setting.
Message
Meaning
Software exception detected! Restart this
console as soon as possible.
An abnormality occurred in software. Restart this control surface
immediately.
Software exception detected! Restart this
editor as soon as possible.
An abnormality occurred in software. Restart Editor immediately.
Song file not found!
The song file to play cannot be found.
Sync error! [XX]
The digital input signal at the [XX] connector is not syncing with
the master clock. Make sure that the input signal is syncing with
the master clock. Otherwise, noise may be heard.
Temporary channel link released
A temporary channel link was released.
This device is currently online and cannot
be changed.
This device is currently on-line. You cannot change the device
type.
This feature is not available in editor
software
This feature is not available in Editor.
This feature will be supported in a future
software release.
This feature will be supported in a future software update.
This item is read only!
You cannot modify this item.
This message appears if you attempt to change a Factory preset
title.
Too many Monitor Sources! Max. 8
sources can be assigned.
Too many sources have been selected for monitor input. (Up to
eight sources can be assigned.)
Total MY slot power capability exceeded!
Remove cards from unit XX
Normal operation is not possible because the power at the MY
slots exceeds the maximum power allowed. Remove the MY
cards from unit XX. For information on the maximum number of
MY cards that can be used, please visit the Yamaha Pro Audio
website at:
http://www.yamahaproaudio.com/
TWINLANe total cable length too long (HY
SLOT X)
The total length of cables on the TWINLANe network (HY slot X)
is too long.
TWINLANe clock master not found!
The TWINLANe clock master cannot be found. One DSP engine
in the system must be assigned as the word clock master.
TWINLANe optical receiver input power
margin low [XXX]
The power of the optical receiver for communication on the
TWINLANe network is getting low. Check the cable integrity and
connection, and clean the connection.
TWINLANe: ring connection open! [XXX]
Check cable connection.
The system detected disconnection of the ring connection on the
TWINLANe network. Check the cable integrity and connection.
TWINLANe: wrong cable connection!
The system detected an incorrect TWINLANe cable connection.
Make sure that the ring connection is proper by connecting the
cables in the order of IN-OUT-IN-OUT.
Unassigned encoder
You operated an encoder for which no function is assigned.
Unsupported file format!
An unsupported file format was detected and the file failed to
load.
Unsupported USB storage format!
The USB storage format is incorrect or unsupported.
Message
Meaning
