Yamaha RIVAGE PM10, Operation Manual

Page: 32 / 375

CONTENTS
Cue
32
RIVAGE PM10 Operation Manual
In order to check the sound of a selected individual channel or DCA, you can output it to
MONITOR OUT, CUE OUT, or PHONES OUT for auditioning.
The RIVAGE PM10 system provides two cue outputs, CUE A and CUE B.
Number of systems
The RIVAGE PM10 features two cue outputs: CUE A and CUE B.
Structure of the cue circuit
The cue circuit is stereo, with an L-channel and R-channel.
1
CUE TRIM
INPUT CUE/OUTPUT CUE specify the monitor level when PFL is selected.
DCA CUE specifies the monitor level when DCA is cued. DCA UNITY lets you monitor each
DCA at unity gain (the same level as when the DCA fader is set to 0 dB).
2 CUE OUT MODE
Downmixes the L/R signals to monaural.
3 DELAY
Allows you to delay the cue signal. You can specify up to 1000 msec.
4
INSERT
A plug-in, GEQ, or PEQ can be inserted. This is a single insert point which is fixed at PRE EQ
(immediately before the EQ).
5 PEQ
A dedicated 8-band parametric EQ for the cue is provided.
6
CUE LEVEL
This adjusts the output level of the CUE channel. The CUE level can also be assigned to a fader.
7 Output structure
• L-channel and R-channel of CUE A
• L-channel and R-channel of CUE B
CUE MODE
You can select either MIX CUE or LAST CUE as the cue mode.
MIX CUE: All selected channels will be mixed and auditioned.
LAST CUE: Only most recently selected channel will be auditioned.
CUE stack
Cue signals are divided into four groups: INPUT CUE group, DCA CUE group, OUTPUT CUE
group, and other CUE group.
The illustration on the right shows the priority of
the [CUE] keys.
After you have switched groups from lower to upper
levels, if you then defeat cue for the upper group,
the previous [CUE] key status of the group
immediately below will be restored. For example, if
you switch groups in the order of OUTPUT CUE
group → DCA CUE group → INPUT CUE group →
Other CUE group, you can then successively defeat
the [CUE] keys (CUE/KEY IN CUE buttons) to
successively restore the [CUE] key status of the
previously-selected group.
CUE/SEL LINK
The [SEL] keys can be linked to the [CUE] key that is pressed. For more information, refer to Part 2.
Cue
MONITOR
SOURCE
SELECT
STEREO
OSC
MIX
MATRIX
TALKBACK
INPUT CH
(DIRECT OUT)
CUE TRIM
L
R
C
DELAY
DIMMER
ON CUE
MONITOR
OUT
MODE
CUE OUT
MODE
CUE SOLO LOGIC
LEVEL
PRE EQ
(CUE)
PRE DELAY
(CUE)
POST DELAY
(CUE)
LEVEL
CUE
OUT
MONITOR A OUT
L
R
L
R
C
PHONES A-B
[PHONES OUT A, B]
DA
PHONES
LEVEL
Tip
Ring
Sleeve
POST EQ
(CUE)
PRE DELAY
(MONITOR)
CUE
PRE DELAY
POST DELAY
MONITOR
PRE DELAY
POST DELAY
DIMMER/
DIMMER
ON
TALKBACK
DIMMER
ON
TALKBACK
L R+C
DOWN-
MIX
PH
O
N
E
S
LE
VE
L L
IN
K
PHONES
LEVEL
LINK
INSERT
INSERT
PLUG-IN
INSERT
POST DELAY
(MONITOR)
MONITOR
PEQ
CUE PEQ
CUE/SOLO
LOGIC
L
R
C
CUE A/B
L R
4
6 2 3 5 1 7
4
Other CUE gro u p
INPUT CUE gro u p
DCA CUE gro u p
OUTPUT CUE gro u p