GE Medical Systems 500 User Manual Download Page 601

Page: 601 / 636

Operator Diagnostics

LOGIQ 500 Basic Users Manual
2276612–100 Rev. 0

16–35



Accessing Diagnostics

To access the available diagnostics, select the Set Up Top Menu.

Preset

Program

Set Up

ECG

System

Paramtr

Custom

Display

Diag.

User

Define

Utility

Save

Values

Figure 16–9. Set Up Sub-Menu

Select DIAG from the Set Up Sub-Menu. The diagnostic test
menu appears on the screen.

Figure 16–10. Diagnostic Test-Menu

Type in the desired test number and press Return. The test
begins running or the test pattern is displayed.

EXE TIME is the test execution time. (The time needed to run
the test.)

Summary of Contents for 500





























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 500

Reviews:

GE Medical Systems 500, User Manual, Page: 601 / 636

Search results

Summary of Contents for 500

Reviews: