GE Medical Systems 500 User Manual Download Page 579

Page: 579 / 636

System Care and Maintenance

LOGIQ 500 Basic Users Manual
2276612–100 Rev. 0

16–13



Cleaning the system (cont’d)

Monitor

To clean the monitor face and filter:

Remove the monitor filter as shown in Figure 16–1.

Figure 16–1. Monitor Filter Removal

Slide the filter clamps towards the monitor sides.

Pull the filter clamps out.

Summary of Contents for 500





























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 500

Reviews:

GE Medical Systems 500, User Manual, Page: 579 / 636

Search results

Summary of Contents for 500

Reviews: