GE Medical Systems 500 User Manual Download Page 556

Page: 556 / 636

Preparing for a Biopsy

LOGIQ 500 Basic Users Manual

2276612–100 Rev. 0

15–44



Fixed Needle Guide Assembly (cont’d)

Figure 15–20. Needle Barrels

Place the needle barrel into the needle clip with the desired
gauge facing the needle clip and snap into place.

Figure 15–21. Needle Barrel Installation

Ensure that all guide parts are seated properly prior to
perfoming a biopsy.

CAUTION

Summary of Contents for 500





























































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 500

Reviews:

GE Medical Systems 500, User Manual, Page: 556 / 636

Search results

Summary of Contents for 500

Reviews: