manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Share
Download
GigaDevice Semiconductor GD32F20 Series User Manual Download Page 4

 

                                                                                                             

GD32F20x User Manual

 

4 

 

5.2.

 

Clock control unit (CCTL) ..................................................................................................... 81

 

5.2.1.

 

Overview

 ............................................................................................................................................ 81

 

5.2.2.

 

Characteristics

................................................................................................................................... 83

 

5.2.3.

 

Function overview

 ............................................................................................................................. 83

 

5.3.

 

Register definition .............................................................................................................. 88

 

5.3.1.

 

Control register (RCU_CTL)

 ............................................................................................................ 88

 

5.3.2.

 

Configuration register 0 (RCU_CFG0)

 .......................................................................................... 90

 

5.3.3.

 

Interrupt register (RCU_INT)

 ........................................................................................................... 93

 

5.3.4.

 

APB2 reset register (RCU_APB2RST)

 .......................................................................................... 96

 

5.3.5.

 

APB1 reset register (RCU_APB1RST)

 .......................................................................................... 99

 

5.3.6.

 

AHB1 enable register (RCU_AHB1EN)

 ....................................................................................... 101

 

5.3.7.

 

APB2 enable register (RCU_APB2EN)

 ....................................................................................... 103

 

5.3.8.

 

APB1 enable register (RCU_APB1EN)

 ....................................................................................... 106

 

5.3.9.

 

Backup domain control register (RCU_BDCTL)

 ........................................................................ 109

 

5.3.10.

 

Reset source/clock register (RCU_RSTSCK)

 ............................................................................ 110

 

5.3.11.

 

AHB1 reset register (RCU_AHB1RST)

 ....................................................................................... 112

 

5.3.12.

 

Configuration register 1 (RCU_CFG1)

 ........................................................................................ 112

 

5.3.13.

 

Deep-sleep mode voltage register (RCU_DSV)

 ........................................................................ 114

 

5.3.14.

 

AHB2 enable register (RCU_AHB2EN)

 ....................................................................................... 115

 

5.3.15.

 

APB2 additional enable register (RCU_ADDAPB2EN)

 ............................................................. 116

 

5.3.16.

 

APB1 additional enable register (RCU_ADDAPB1EN)

 ............................................................. 117

 

5.3.17.

 

AHB2 reset register (RCU_AHB2RST)

 ....................................................................................... 117

 

5.3.18.

 

APB2 additional reset register (RCU_ADDAPB2RST)

 ............................................................. 118

 

5.3.19.

 

APB1 additional reset register (RCU_ADDAPB1RST)

 ............................................................. 119

 

5.3.20.

 

Configuration register 2 (RCU_ CFG2)

 ....................................................................................... 120

 

5.3.21.

 

PLLT control register (RCU_PLLTCTL)

 ....................................................................................... 121

 

5.3.22.

 

PLLT interrupt register (RCU_PLLTINT)

 ..................................................................................... 122

 

5.3.23.

 

PLLT configuration register (RCU_PLLTCFG)

 ........................................................................... 122

 

6.

 

Interrupt/event controller(EXTI)

 ............................................................................. 125

 

6.1.

 

Overview ......................................................................................................................... 125

 

6.2.

 

Characteristics ................................................................................................................. 125

 

6.3.

 

Interrupts function overview ............................................................................................ 125

 

6.4.

 

External interrupt and event (EXTI) block diagram ............................................................ 129

 

6.5.

 

External Interrupt and Event function overview ................................................................ 129

 

6.6.

 

Register definition ............................................................................................................ 131

 

6.6.1.

 

Interrupt enable register (EXTI_INTEN)

 ...................................................................................... 131

 

6.6.2.

 

Event enable register (EXTI_EVEN)

 ............................................................................................ 131

 

6.6.3.

 

Rising edge trigger enable register (EXTI_RTEN)

 ..................................................................... 132

 

6.6.4.

 

Falling edge trigger enable register (EXTI_FTEN)

 .................................................................... 132

 

6.6.5.

 

Software interrupt event register (EXTI_SWIEV)

 ....................................................................... 132

 

6.6.6.

 

Pending register (EXTI_PD)

 .......................................................................................................... 133

 

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands