manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Share
Download
GigaDevice Semiconductor GD32F20 Series User Manual Download Page 140

 

                                                                                                             

GD32F20x User Manual

 

140 

 

7.4. 

Remapping function I/O and debug configuration 

7.4.1. 

Introduction 

In order to expand the flexibility of the GPIO or the usage of peripheral functions, each I/O pin 

can be configured to have up to four different functions by setting the AFIO Port Configuration 

Register (AFIO_PCF0/AFIO_PCF1). Suitable pinout locations can be selected by using the 

peripheral IO remapping function. Additionally, various GPIO pins can be selected to be the 

EXTI interrupt line by setting the relevant EXTI Source Selection Register (AFIO_EXTISSx) 

to trigger an interrupt or event. 

7.4.2. 

Main features 

 

APB slave interface for register access. 

 

EXTI source selection. 

 

Each pin has up to four alternative functions for configuration. 

7.4.3. 

JTAG/SWD alternate function remapping 

The debug interface signals are mapped on the GPIO ports as shown in table below. 

Table 7-2. Debug interface signals 

Alternate function

 

GPIO port

 

JTMS / SWDIO

 

PA13

 

JTCK / SWCLK

 

PA14

 

JTDI

 

PA15

 

JTDO / TRACESWO

 

PB3

 

NJTRST

 

PB4

 

TRACECK

 

PE2

 

TRACECK0

 

PE3

 

TRACECK1

 

PE4

 

TRACECK2

 

PE5

 

TRACECK3

 

PE6

 

To reduce the number of GPIOs used to debug, user can configure SWJ_CFG [2:0] bits in 

the AFIO_PCF0 to different value. Refer to table below. 

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands