manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Introducing the GigaDevice Semiconductor GD32F20 Series - a cutting-edge product with exceptional features. Unlock the full potential of your device by accessing the comprehensive User Manual, available for free download at manualshive.com. This manual is your ultimate guide to harnessing the power of GD32F20, ensuring optimal performance and user satisfaction.

Share
Download
background image

 

                                                                                                             

GD32F20x User Manual

 

859 

 

0: Timestamp update value is added to system time 

1: Timestamp update value is subtracted from system time 

30:0 

TMSUSS[30:0] 

Timestamp update subsecond bits 

These bits are used for initializing or adding/subtracting to subsecond of the system 

time 

27.4.39. 

PTP time stamp addend register (ENET_PTP_TSADDEND) 

Address offset: 0x0718 

Reset value: 0x0000 0000 

This register value is used only in fine update mode for  adjusting the clock frequency. This 

register  value  is  added  to  a  32-bit  accumulator  in  every  clock  cycle  and  the  system  time 

updates when the accumulator reaches overflow. 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

TMSA[31:16] 

rw 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

TMSA[15:0] 

rw 

 

Bits 

Fields 

Descriptions 

31:0 

TMSA[31:0] 

Time stamp addend bits 

These  registers  contain  a  32-bit  time  value  which  is  added  to  the  accumulator 

register to achieve time synchronization 

27.4.40. 

PTP expected time high register (ENET_PTP_ETH) 

Address offset: 0x071C 

Reset value: 0x0000 0000 

31 

30 

29 

28 

27 

26 

25 

24 

23 

22 

21 

20 

19 

18 

17 

16 

ETSH[31:16] 

rw 

15 

14 

13 

12 

11 

10 

9 

8 

7 

6 

5 

4 

3 

2 

1 

0 

ETSH[15:0] 

rw 

 

Bits 

Fields 

Descriptions 

31:0 

ETSH[31:0] 

Expected time high bits 

These bits store the expected target second time.   

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F20 Series

wattio AIR Read Me preview
AIR
Brand: wattio Pages: 20
Tapeswitch C6 Technical Manual preview
C6
Brand: Tapeswitch Pages: 13
Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Brand: Panasonic Pages: 45
Banner SC22-3 Quick Start Manual preview
SC22-3
Brand: Banner Pages: 15
Data Aire dap4 touch Protocol Manual preview
dap4 touch
Brand: Data Aire Pages: 13
vacuubrand CVC 3000 Instructions For Assembly preview
CVC 3000
Brand: vacuubrand Pages: 12
Vacon 100 INDUSTRIAL Installation And User Manual preview
100 INDUSTRIAL
Brand: Vacon Pages: 47
Vacon 100 flow Installation Instruction preview
100 flow
Brand: Vacon Pages: 40
Hiwin RC4 Original Instruction preview
RC4
Brand: Hiwin Pages: 99
ZKTeco LockerPad-7B User Manual preview
LockerPad-7B
Brand: ZKTeco Pages: 27
Sunlight Supply TITAN CONTROLS KRONUS 2 Instruction Manual preview
TITAN CONTROLS KRONUS 2
Brand: Sunlight Supply Pages: 4
Universal Remote Control total control MRX-10 Owner'S Manual preview
total control MRX-10
Brand: Universal Remote Control Pages: 16
Velp Scientifica F201A0505 Instruction Manual preview
F201A0505
Brand: Velp Scientifica Pages: 24
Davey Torrium2 Installation And Operating Instructions Manual preview
Torrium2
Brand: Davey Pages: 8
watt box WB-150-IPW-1B-2 Quick Start Manual preview
WB-150-IPW-1B-2
Brand: watt box Pages: 12
rotork CQP Installation Commissioning Maintenance Manual preview
CQP
Brand: rotork Pages: 33
Tektronix TLA 711 Installation Manual preview
TLA 711
Brand: Tektronix Pages: 82
Fego Precision Industrial TP48 Instructions preview
TP48
Brand: Fego Precision Industrial Pages: 2

Brands by name

Popular brands

Load more brands