manualshive.com logo in svg

GigaDevice Semiconductor GD32F20 Series, User Manual

Introducing the GigaDevice Semiconductor GD32F20 Series - a cutting-edge product with exceptional features. Unlock the full potential of your device by accessing the comprehensive User Manual, available for free download at manualshive.com. This manual is your ultimate guide to harnessing the power of GD32F20, ensuring optimal performance and user satisfaction.

Share
Download
background image

 

                                                                                                             

GD32F20x User Manual

 

556 

 

This bit is set when the transmit buffer is empty, the software can write the next data to the 

transmit buffer by writing the SPI_DATA register.   

 

Receive buffer not empty flag (RBNE) 

This bit is set when receive buffer is not empty, which means that one data is received and 

stored in the receive buffer, and software can read the data by reading the SPI_DATA register. 

 

SPI Transmitting On-Going flag (TRANS) 

TRANS is a status flag to indicate whether the transfer is on-going or not. It is set and cleared 

by internal hardware and not controlled by software. This flag 

doesn’t generate any interrupt. 

21.6.2. 

Error conditions 

 

Configuration Fault Error (CONFERR) 

CONFERR is an error flag in master mode. In NSS hardware mode and the NSSDRV is not 

enabled, the CONFERR is set when the NSS pin is pulled low. In NSS software mode, the 

CONFERR is set when the SWNSS bit is 0. When the CONFERR is set, the SPIEN bit and 

the MSTMOD bit are cleared by hardware, the SPI is disabled and the device is forced into 

slave mode. 

The  SPIEN  and  MSTMOD  bit  are  write  protection  until  the  CONFERR  is  cleared.  The 

CONFERR bit of the slave cannot be set. In a multi-master configuration, the device can be 

in slave mode  with CONFERR bit set,  which means there might have  been a  multi-master 

conflict for system control. 

 

Rx Overrun Error (RXORERR) 

The RXORERR bit is set if a data is received when the RBNE is set. That means, the last 

data  has  not  been  read  out  and  the  newly  incoming  data  is  received.  The  contents  of  the 

receive  buffer  are  not  covered  by  the  newly  incoming  data,  so  the  newly  incoming  data  is 

missing.   

 

CRC Error (CRCERR) 

When the CRCEN bit is set, the CRC calculation result of the received data in the SPI_RCRC 

register  is  compared  with  the  received  CRC  value  after  the  last  data,  the  CRCERR  is  set 

when they are different.   

Table 21-4. SPI interrupt requests 

Flag

 

Description

 

Clear Method

 

Interrupt 

Enable bit

 

TBE 

Transmit buffer empty 

Write SPI_DATA register. 

TBEIE 

RBNE 

Receive buffer not empty 

Read SPI_DATA register 

RBNEIE 

CONFERR    Configuration Fault Error 

Read or write SPI_STAT 

register, then write SPI_CTL0 

register.

 

ERRIE 

Summary of Contents for GD32F20 Series























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F20 Series

OEG KMS Manual preview
KMS
Brand: OEG Pages: 168
Unipower PCM500 Series Operating Manual preview
PCM500 Series
Brand: Unipower Pages: 24
Madison AV PC2 Reference Manual preview
PC2
Brand: Madison AV Pages: 2
Idex Pulsafeeder MPC Vector Installation, Operation & Maintenance Manual preview
Pulsafeeder MPC Vector
Brand: Idex Pages: 114
NEC uPD78F4225Y Manual preview
uPD78F4225Y
Brand: NEC Pages: 30
Atari IDEa How To Connect preview
IDEa
Brand: Atari Pages: 3
Quicksmart EtherRain User Manual preview
EtherRain
Brand: Quicksmart Pages: 10
Aerotech Ensemble HLe Hardware Manual preview
Ensemble HLe
Brand: Aerotech Pages: 112
Edge Electrons EDGEIQ EE-202-0050 Installation, Commissioning And Operation Manual preview
EDGEIQ EE-202-0050
Brand: Edge Electrons Pages: 32
Instrutech VGC301A User Manual preview
VGC301A
Brand: Instrutech Pages: 34
Zennio MINiBOX 40 v3 Quick Start Manual preview
MINiBOX 40 v3
Brand: Zennio Pages: 2
Danfoss PVE 4 Series Technical Information preview
PVE 4 Series
Brand: Danfoss Pages: 56
3Ware 720-0104-00 Manual preview
720-0104-00
Brand: 3Ware Pages: 50
SATA air regulator belt plus Operating Instructions Manual preview
air regulator belt plus
Brand: SATA Pages: 158
CSI Wireless SATLOC GPSteer LiteStar II Quick Reference Manual preview
SATLOC GPSteer LiteStar II
Brand: CSI Wireless Pages: 7
ICON ProCon D400 Series Operating Manual preview
ProCon D400 Series
Brand: ICON Pages: 28
Xinje XSA330-W User Manual preview
XSA330-W
Brand: Xinje Pages: 41
Whelen Engineering Company MPC03 Installation & Operating Manual preview
MPC03
Brand: Whelen Engineering Company Pages: 10

Brands by name

Popular brands

Load more brands