![background image](http://html1.mh-extra.com/html/ducati/monster-s4-fogarty-2002/monster-s4-fogarty-2002_workshop-manual_2537693056.webp)
56
Registrazioni e regolazioni / Settings and adjustments
Posizione del potenziometro
Agire nel modo seguente dopo aver
portato a regime termico il motore:
❍
staccare il serbatoio dal telaio e
rimuovere l’air-box nel modo
descritto al capitolo “Smontaggio
scatola filtro aria” nella Sezione
"
Mototelaio
".
❍
Allentare completamente o
staccare il cavo di comando
acceleratore e dello starter dal
corpo farfallato per impedire che
uno dei due cavi non permetta la
chiusura della farfalla MASTER.
❍
Svitare la vite di registro (1) della
farfalla MASTER in modo che non
appoggi sul relativo finecorsa.
❍
Agire sul dado (2) del tirante di
collegamento delle farfalle per
accertarsi che la farfalla MASTER
(quella del lato potenziometro)
risulti completamente chiusa.
In alternativa è possibile controllare
se la farfalla del cilindro verticale è
completamente aperta.
▲
Collegare il cavo alimentazione
(3, cod.
514.1.034.1A
) alla presa RC
586 (centrale) del Mathesis
utilizzando il cavo adattatore presa
batteria (8, cod.
514.1.038.1A
) e
collegarlo alla presa A del cavo di
alimentazione e alla batteria della
moto.
❍
Disconnettere il potenziometro
dal cablaggio della moto.
Attenzione
Non collegare la presa di
diagnosi della moto al cavo di
alimentazione del Mathesis (presa A).
❍
Collegare il cavo (4, cod.
514.1.032.1A
) per il collegamento
del potenziometro alla presa COM2
del Mathesis.
❍
Collegare al cavo (4) l’adattatore
(5, cod.
514.1.033.1A
) e
quest’ultimo al potenziometro (6).
Registrazione del
potenziometro
❍
Introdurre la “Memory card”
nello strumento, entrare nella
funzione "Potenziometro" del menù
"Ausiliari". A questo punto si legge la
tensione in uscita del
potenziometro, con la farfalla
completamente chiusa. Il valore di
riferimento è
150 mV±15
.
❍
In caso di valori differenti,
allentare le 2 viti (7) di fissaggio
potenziometro e, mantenendo in
posizione di chiusura la farfalla
MASTER, ruotare il potenziometro
fino a leggere il valore prescritto.
❍
Serrare le viti (7) del
potenziometro.
❍
Scollegare la connessione del
“MATHESIS” dal potenziometro e
riconnettere il cablaggio della moto.
Throttle sensor position
Warm up the engine and then
proceed as follows:
❍
Remove the fuel tank and the air
box as specified in “Removing the
air box”, under “
Frame
” section.
❍
Fully loosen or disconnect the
throttle and choke control cables
from the throttle body so that no
cable can interfere with MASTER
throttle closing.
❍
Unscrew the MASTER throttle
adjuster screw (1) so that it is not
resting on its end stop.
❍
Turn the nut (2) on the throttle
linkage rod to make sure that the
MASTER throttle (on the sensor
side) is fully closed. As an
alternative, it is possible to check if
the vertical cylinder throttle is fully
open.
▲
Connect Mathesis tester power
cable (3, part no.
514.1.034.1A
) to
the Mathesis tester RC586 (central)
port with battery adapter cable (8,
part no.
514.1.038.1A
) and then
connect it to power cable plug (A)
and to the bike battery.
❍
Disconnect throttle position
sensor from wiring harness.
Warning
Do not connect the bike
diagnosis port to the Mathesis
power cable (A port)
❍
Connect the throttle position
sensor cable (4, part No.
514.1.032.1A
) to the Mathesis
COM2 port.
❍
Connect the adapter (5, part No.
514.1.033.1A
) to cable (4) and then
connect the adapter to the throttle
position sensor (6).
Adjusting the throttle position
sensor
❍
Insert the “Memory card” into
the tester, access the “Throttle
position sensor” function into the
“Auxiliary” menu. The throttle
position sensor output voltage
value, with throttle fully closed, will
appear. The reference value is
150
mV±15
.
❍
If the reading is outside the
specified limits, loosen the two
screws (7) on the throttle position
sensor. Keeping the MASTER
throttle closed, turn the throttle
position sensor until reading the
recommended value.
❍
Tighten throttle position sensor
screws (7).
❍
Disconnect the “MATHESIS”
tester from the throttle position
sensor and reconnect bike wiring.
2
1
5
A
4
3
7
6
3
A
8
Summary of Contents for monster S4 fogarty 2002
