© Jack Sealey Limited
Original Language Version
INSTRUCTIONS FOR:
WELDING HELMETS AUTO DARKENING
SHADE
9-13
MODEL NO’S:
PWH598 SERIES
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
Refer to instruction
Manual
1. SAFETY
WARNING!
THIS HELMET IS NOT SUITABLE FOR USE WITH LASER OR GAS-WELDING.
Ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. The helmet will not offer
protection against misuse of workshop tools, equipment or accessories.
The helmet will not protect against harmful gasses generated by the welding process.
Maintain the
helmet in good condition and protect cartridge from liquid and dirt contact.
Replace the protective lens regularly and replace any damaged or worn parts.
Use genuine parts only. Non authorised parts may be
dangerous and will invalidate the warranty.
NEVER
open or tamper with the shade cartridge.
Select the shade level before use.
Ensure the front cover lens is securely in place before use.
Fit the helmet and adjust the head band so the helmet will sit as low and near to the face as possible.
Use helmet only in temperatures ranging from -5
o
C to 55
o
C (23
o
F to 131
o
F).
The eye protective plate in the helmet is
NOT
unbreakable. The helmet will not protect you against severe impact hazards
The helmet will only protect the eyes and face from radiation and sparks.
Remove ill fitting clothing, remove ties, watches, rings, and other loose jewellery.
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
Keep children and unauthorised persons away from the working area.
WARNING! DO NOT
use the helmet if damaged or you suspect it may be faulty.
DO NOT
use helmet unless you have been instructed in its use by a competent person.
DO NOT
get the helmet wet or use in damp or wet locations.
DO NOT
leave work place with helmet in lowered position, as bright light source may darken cartridge unexpectedly.
DO NOT
place the helmet on a hot surface.
DO NOT
use helmet without front cover lens and frame fitted. To do so will invalidate the warranty.
Clean helmet (see section 5.4) and store the helmet in a safe, dry, childproof location.
Before welding always inspect the cartridge filter to ensure that it is not damaged. To test the filter prior to welding, direct the front of the
cartridge filter to a bright light source which will cause the lens to darken. Then using the hand rapidly cover and uncover the sensor. The
filter should lighten momentarily then return to a dark state.
DANGER!
If, at any time, the face plate in the cartridge fails to darken when exposed to a welding spark,
DO NOT USE
. Remove
cartridge and return to the dealer for checking. Continued use of the product knowing that the auto darkening feature is not
functioning may damage the eyes and cause blindness.
2. INTRODUCTION
Welding helmet with infinitely adjustable shade control between 9-13. Complies with BS EN 379, BS EN 175 and DIN standards. Fully automatic
switching from light to dark on striking arc. Shade is selected by a rotary knob on side of helmet. Grinding function enables user to grind without
removing mask. Solar panel power supply - no batteries required. Features sensitivity and delay controls for switching light to dark. Coloured
chrome finish and contoured design helmet with adjustable headband for added comfort. Suitable for MIG, TIG and arc welding.
3. SPECIFICATION
Model No:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PWH598
Shade Active:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-13 Variable
Shade Inactive: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Grinding Function: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Yes
Viewing Area:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 x 42mm
Operating Time Light/Dark: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.04ms
Operating Temperature:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5° to 55°C
Power: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solar Cells
Weight:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490g
PWH598 Series Version:1 - 08/02/16
