![background image](http://html1.mh-extra.com/html/ducati/monster-s4-fogarty-2002/monster-s4-fogarty-2002_workshop-manual_2537693061.webp)
Registrazioni e regolazioni / Settings and adjustments
61
A
C
B
REGISTRAZIONE POSIZIONE
PEDALE COMANDO CAMBIO
E FRENO POSTERIORE
Per assecondare le esigenze di
guida di ogni pilota è possibile
modificare la posizione delle leve
comando cambio e freno posteriore
rispetto all’appoggiapiedi.
Le figure riportano le quote per
ristabilire la configurazione originale
di detti comandi.
Per modificare la posizione della
leva comando cambio agire nel
modo seguente:
❍
Bloccare l’asta (A) e allentare i
controdadi (B) e (C).
Note
Il dado (B) ha un filetto
sinistrorso.
❍
Ruotare l’asta (A) facendo
assumere al pedale cambio la
posizione desiderata.
▲
Serrare contro l’asta entrambi i
controdadi.
Per modificare la posizione della
leva comando freno posteriore agire
nel modo seguente:
❍
Allentare il controdado (D).
❍
Ruotare la vite (E) di registro corsa
pedale fino a stabilire la posizione
desiderata.
▲
Serrare il controdado (D).
●
Verificare, agendo a mano sul
pedale, che questo presenti un
gioco di circa
1,5÷2 mm
prima di
iniziare l’azione frenante.
Se così non risulta occorre
modificare la lunghezza dell’astina di
comando della pompa nel modo
seguente:
❍
Allentare il controdado (F)
sull’astina della pompa.
▲
Avvitare l’astina sulla forcella (G)
per aumentare il gioco o svitarla per
diminuirlo.
▲
Serrare il controdado (F) e
verificare nuovamente il gioco.
ADJUSTING THE POSITION
OF THE GEAR CHANGE AND
REAR BRAKE PEDALS
The position of the gear change and
rear brake pedals in relation to the
footpegs can be adjusted to suit
rider preferred riding position.
When you want to restore the
original configuration, refer to the
dimensions given in the figures at
the side.
To adjust the position of the gear
change pedal, proceed as follows:
❍
Clamp the rod (A) and loosen the
lock nuts (B) and (C).
Note
Lock nut (B) has a left-hand
thread.
❍
Turn the rod (A) until the gear
change pedal is in the position
required.
▲
Tighten the two lock nuts onto
the rod.
To adjust the position of the rear
brake pedal, proceed as follows:
❍
Loosen the lock nut (D).
❍
Turn the pedal travel adjuster
screw (E) until the pedal is in the
position required.
▲
Tighten the lock nut (D).
●
Operate the pedal by hand and
check that there is
1.5 to 2 mm
of
free pedal travel before the brake
begins to operate.
If this is not the case, adjust the
length of the brake cylinder control
rod as follows:
❍
Loosen the lock nut (F) on the
brake cylinder control rod.
▲
To increase the amount of pedal
free travel, screw the rod further
into the fork (G). Unscrew the rod to
decrease.
▲
Tighten the lock nut (F) and check
the amount of pedal free travel.
F
G
D
8 mm
E
Summary of Contents for monster S4 fogarty 2002
