Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 71 / 442

background image

1

Performing Routine Maintenance

Maintaining the Foreline Pump

Thermo Scientific

ISQ 7000 Hardware Manual

43

19. If the GC is powered off, power it on and make sure vacuum compensation is on for the

carrier gas flowing into the mass spectrometer.

20. Purge the foreline pump for 10 minutes using the gas ballast to remove excess gases from

the new oil.

Purging Gas from the Oil in the Foreline Pump

Purging (or decontaminating) the oil in the foreline pump removes dissolved gases and
low-boiling-point liquids from the oil. Purge the oil if it is cloudy or discolored. You can
purge the oil without interrupting system operation.

Set the gas-ballast control to position I or II (0 means closed) to purge the oil.

Changing the Oil in a Foreline Pump

You should change the foreline pump oil every four months or after 3,000 hours of operation.
If you use ammonia as a chemical ionization reagent gas, you should change the oil every
month. Ammonia is highly corrosive and quickly damages the seals in the foreline pump.

To change the oil in the foreline pump:

21. Cool down the GC oven.

WARNING FIRE HAZARD:

If you are using hydrogen, do NOT reach over the top of the

instrument to power it on. Instead, reach around the right side or go to the back of the
instrument and flip up the power switch.

AVERTISSEMENT RISQUE D’INCENDIE

: si vous utilisez de l’hydrogène, ne passez PAS la

main par-dessus l’instrument pour le mettre sous tension. Passez-la plutôt par le côté droit
ou placez-vous derrière l’instrument et activez l’interrupteur d’alimentation.

CAUTION INSTRUMENT DAMAGE:

While the gas is being purged, more oil vapor is

being generated. If you leave the purge open for an excessive amount of time, the pump
oil will become mist, which could damage the pump. Never purge your pump for more
than 10 minutes at a time.

ATTENTION DOMMAGES À L’INSTRUMENT

: lorsque le gaz est en train d’être purgé, cela

génère davantage de vapeur d’huile. Si vous laissez la purge ouverte pendant trop longtemps,
l’huile de la pompe sera transformée en brouillard, ce qui peut endommager la pompe. Ne
purgez jamais votre pompe pendant plus de 10 minutes à la fois.

Note

For best results, change the oil while the foreline pump is still warm. Be careful, as

the oil can be very hot if the pump has been used recently.

Note

If you are running samples, stop the acquisition before powering off the system.

«
...
69
70
71
72
73
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Бренд: ABB Страницы: 8

Бренд: M-system Страницы: 16

Бренд: M-system Страницы: 25

Бренд: OBDPROG Страницы: 8

Бренд: ZHYQ Страницы: 6

Pianovelle GRP3

Бренд: Baldwin Страницы: 34

Бренд: Haltech Страницы: 20

Бренд: bihl+Wiedemann Страницы: 16

D-Mon Class 1000

Бренд: E-Mon Страницы: 26

Бренд: Corentium Страницы: 8

Бренд: Trotec Страницы: 19

Бренд: Proceq Страницы: 36

Бренд: ChallengerOptics Страницы: 22

Бренд: Ametek Страницы: 70

Бренд: SUPMEA Страницы: 21

Бренд: Agatec Страницы: 70

Бренд: National Instruments Страницы: 9

PXI-4070 6 1/2 Digit FlexDMM

Бренд: National Instruments Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды