Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 302 / 442

Advanced Maintenance

Upgrading the ISQ 7000 System Software

274

ISQ 7000 Hardware Manual

Thermo Scientific

3. After the software has located the configuration of the LAN CPU, right-click on the IP

address for the LAN CPU and select

Configure.

4. Click the

Operating Mode

tab, check the Modify checkbox, and click

Settings

5. In the Operating Mode window, enter 30,000 ms for the Inactivity Timeout, then click

OK.

6. Click

to send the new settings to the LAN CPU. You will receive a confirmation

message noting,

Configuration is applied ok

. Click

and close the Network Enabler

tool.

7. Click

again to upload these settings to the LAN adapter.

8. When the settings have been uploaded successfully, you can close the utility and proceed

to the Instrument Configuration process for the TRACE GC Ultra.



To configure NPort Search Utility

1. Open the NPort Search Utility by selecting

Start | All Programs | NPort Search Utility

and locate

NPort Search Utility

2. Right-click on NPort Search Utility and select

Run as Administrator

from the options

(Windows 7).

3. Confirm the User Account Control message so NPort Search can make changes to the

computer (Windows 7).

4. The NPort Search Utility will open.

5. Select

Search

from the tool bar. This will allow the utility to search for IP connections. A

search window will appear.

6. After completing the search, the NPort Search Utility will return with a list of LAN

connections. Select the device corresponding to the TRACE GC Ultra and double-click
on it to bring up the console.

7. Select

Serial Settings

and confirm that the baud rate is set to 38400. Change as applicable

and click

Submit

to save.

8. Select

Operating Settings

and set the inactivity time to 30,000 ms. Click

Submit

to save,

then close the console.

9. Select

Exit

to close the NPort Search Utility.

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды