Thermo Scientific ISQ 7000 Скачать руководство пользователя | Manualshive

Страница: 61 / 442

background image

1

Performing Routine Maintenance

Replacing a Column

Thermo Scientific

ISQ 7000 Hardware Manual

33

Installing the Column in the GC Inlet

1. Remove the current column:

a. Open the front door of the GC.

b. Unscrew the transfer line nut and remove the column from the transfer line.

c.

Unscrew the injector and detector nuts and remove the column.

d. Remove the column from the column rack and from the GC.

2. Connect the new column to the injector inside the GC.

a. Unwind the column enough to easily connect its ends to the injector and detector.

b. Wipe about 100 mm (4 in.) of the column with a tissue soaked in methanol.

c.

Insert the column through the injector retaining nut and ferrule (larger end up). If
the M4 retaining nut is used, slide it on the column through the side cut. Wipe the
column again with a tissue soaked in methanol.

d. Use a scoring wafer to score and break the column about 1 cm (0.4 in.) from the end.

Use a magnifying glass to check for an even, flat cut. Repeat if necessary.

e.

Insert a notched septum on the column to hold the retaining nut at this position.
Thread the retaining nut into the injector but do not tighten.

f.

Ensure that the end of the column is the proper distance (splitless = 5 mm,
split = 10 mm, PTV and PTVBKF = 30 mm) from the back of the injector nut.

g. Adjust the column position so that the septum contacts the bottom of the retaining

nut. Use your fingers to tighten the retaining nut until it starts to grip the column.

h. Tighten the column nut finger-tight until it starts to grip the column plus a quarter

turn.

CAUTION BURN HAZARD:

The oven may be hot. Allow it to cool to room temperature

before opening it. The injector will still be hot, so do not touch it.

ATTENTION RISQUE DE BRÛLURE :

le four peut être chaud. Laissez-le refroidir à la

température ambiante avant de l’ouvrir. L’injecteur sera toujours chaud, donc ne le touchez
pas.

Note

Wear clean, lint- and powder-free gloves when you handle the column and

injector ferrule.

Tip

Slide a notched septum on the column before the injector retaining nut to

make it easier to measure the proper distance between the nut and end of the
column.

«
...
59
60
61
62
63
...
»

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

LevelMaster 7100

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 4

Бренд: XS Scuba Страницы: 24

Бренд: Datavideo Страницы: 26

Бренд: Datcon Страницы: 84

Бренд: Xylem Страницы: 19

Бренд: Keeler Страницы: 54

Бренд: ASCEL Electronic Страницы: 64

Бренд: FMS Страницы: 12

Бренд: DODODUCK Страницы: 2

Бренд: Spasciani Страницы: 26

Бренд: Guru Home Systems Страницы: 20

micro-TRI-gloss ?

Бренд: BYK Страницы: 174

Бренд: Novus Страницы: 52

Бренд: Rockler Страницы: 4

Бренд: X-Rite Страницы: 21

Бренд: DeNovix Страницы: 93

Бренд: ZETA Music Systems Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды