Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 115 / 442

Performing Routine Maintenance

Cleaning the Ion Source Cartridge

Thermo Scientific

ISQ 7000 Hardware Manual

Figure 86.

Reattaching the Filament Wire to the Source Interface Board

10. Center the manifold door so that the screw holes are aligned with the manifold. And

insert the four manifold screws, tightening each finger-tight such that the o-ring is
engaged on every surface.

11. Tighten the four manifold screws using a T20 Torxhead screwdriver.

12. Tighten the vent valve knob completely by turning it approximately one turn clockwise.

13. Close the front door of the instrument.

14. For optimal performance, wait at least fifteen minutes for the ion source to heat up to the

same temperature as the inside of the instrument. Otherwise, the masses or intensities
may be different.

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды