manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

 

2 

Troubleshooting

Investigating Tuning Issues

Thermo Scientific

ISQ 7000 Hardware Manual

143

Tune is interrupted.

Cannot find calibration gas peaks.

Cannot perform detector gain calibration.

Cannot calibrate resolution.

Possible Remedy

Make sure the computer is not set to go into Standby mode while you are acquiring data for your tune. Otherwise, it may interrupt your 
tune.

Possible Remedies

Remove and replace the ion source cartridge. See 

Ion Source Cartridge

 for instructions.

Check the Air/Water Spectra to confirm the presence of spectra. If none are present, refer to 

Investigating RF/DC Issues

.

Check the calibrant reservoir and add 100 μL (max) of FC 43, if necessary. See 

Maintaining the Calibration Gas Module

 for details.

Make sure the EI ion volume and lenses are properly installed and clean. 

Make sure the filament is not blown.

Make sure the vacuum is functioning properly.

Make sure the vacuum interlock lever is in the down position.

Make sure the stainless steel tubing inside the manifold is connected to the mixing chamber.

Possible Remedies

Make sure you have an ion signal. The gain tune uses ions, so the system must have a signal to start.

Replace the electron multiplier if the voltage required to generate 3 x 10

5

 gain on your electron multiplier is approaching 3000 V.

Run the detector check diagnostic. Troubleshoot any reported failures if the diagnostic fails. Check the detector, feedthrough, and wires for 
dust if the diagnostic fails for high noise.

Possible Remedies

Allow contaminants to pump away so they do not interfere with the masses selected for resolution tuning.

Run manual tune to set the RF frequency and save the tune file to the instrument that the AutoTune needs to use to start tuning. Select Air 
& Water /Tune from the ISQ 7000 Dashboard to launch ISQ Manual Tune.

Create a starting tune file using manual tune. Select Air & Water /Tune from the ISQ 7000 Dashboard to launch ISQ Manual Tune.

Confirm that the correct ion volume is installed in the instrument. For example, a CI ion volume may cause an EI tune to fail.

Confirm that the calibration gas reservoir has FC 43 present.

Confirm that the Q1 Voltage or Repeller Voltage in the Auto Tune starting tune file are not set too high to cause mass peak broadening.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Kawai ES100 Technical Speci? Cations preview
ES100
Бренд: Kawai Страницы: 5
Jata hogar 80 Instructions Manual preview
80
Бренд: Jata hogar Страницы: 12
A&D SV-1A Instruction Manual preview
SV-1A
Бренд: A&D Страницы: 102
Xsens DOT Quick Setup Manual preview
DOT
Бренд: Xsens Страницы: 4
Eastron SDM120 Series Manual preview
SDM120 Series
Бренд: Eastron Страницы: 2
EASTERN INSTRUMENTS CentriFlow Quick Start Manual preview
CentriFlow
Бренд: EASTERN INSTRUMENTS Страницы: 3
Kathrein MSK 15 Mode D'Emploi preview
MSK 15
Бренд: Kathrein Страницы: 10
Percussion Play Babel Drum Installation Instructions Manual preview
Babel Drum
Бренд: Percussion Play Страницы: 3
Motortech EasyNOx Operating Manual preview
EasyNOx
Бренд: Motortech Страницы: 142
HBM T10F Mounting Instructions preview
T10F
Бренд: HBM Страницы: 84
Sonel CMP-400 User Manual preview
CMP-400
Бренд: Sonel Страницы: 84
R&S FSH series Quick Start Manual preview
FSH series
Бренд: R&S Страницы: 130
MEWOI MEWOI9000G User Manual preview
MEWOI9000G
Бренд: MEWOI Страницы: 21
Welch Allyn AM282 Directions For Use Manual preview
AM282
Бренд: Welch Allyn Страницы: 32
red lion PAXLI Data Sheet / Manual preview
PAXLI
Бренд: red lion Страницы: 8
Badger Meter Recordall Disc Series Installation Manual preview
Recordall Disc Series
Бренд: Badger Meter Страницы: 4
Gelia 4000070701 Manual preview
4000070701
Бренд: Gelia Страницы: 4
Bartington Grad-13 Series Operation Manual preview
Grad-13 Series
Бренд: Bartington Страницы: 39

Бренды по названию

Популярные бренды

Загрузить еще бренды