manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

Preface

Safety and Special Notices

xvi

ISQ 7000 Hardware Manual

Thermo Scientific

Safety Symbols and Signal Words

All safety symbols are followed by 

WARNING

 or 

CAUTION

, which indicates the degree of risk 

for personal injury, instrument damage, or both. Cautions and warnings are following by a 
descriptor. A 

WARNING

 is intended to prevent improper actions that 

could

 cause personal 

injury. A 

CAUTION

 is intended to prevent improper actions that 

might 

cause personal injury 

or instrument damage. You can find the following safety symbols on your instrument or in 
this guide.

Symbol

Descriptor

BIOHAZARD: 

Indicates that a biohazard 

will

, 

could

, or 

might

 occur.

BURN HAZARD: 

 Alerts you to the presence of a hot surface that 

could 

or

 

might 

cause

 

burn injuries.

ELECTRICAL SHOCK HAZARD: 

 Indicates that an electrical shock 

could 

or 

might 

occur.

FIRE HAZARD:  

 Indicates a risk of fire or flammability 

could 

or

 might

 occur.

FLAMMABLE GAS HAZARD:

 Alerts you to gases that are compressed, 

liquefied or dissolved under pressure and can ignite on contact with an 
ignition source. This symbol indicates this risk 

could

 or 

might 

cause physical 

injury.

GLOVES REQUIRED: 

 Indicates that you must wear gloves when performing 

a task or physical injury 

could 

or 

might

 occur.

HAND AND CHEMICAL HAZARD:  

Indicates that chemical damage or 

physical injury 

could 

or 

might

 occur.

INSTRUMENT DAMAGE: 

 Indicates that damage to the instrument or 

component 

might 

occur. This damage might not be covered under the 

standard warranty.

LIFTING HAZARD: 

 Indicates that a physical injury 

could

 or 

might

 occur if 

two or more people do not lift an object.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

Baker Hughes Masoneilan 12400 Series Instruction Manual & Safety Manual preview
Masoneilan 12400 Series
Бренд: Baker Hughes Страницы: 81
Hammond Organ A-100 Series Theory Of Operation preview
A-100 Series
Бренд: Hammond Organ Страницы: 25
Hammond Organ L-100 Series Service Manual preview
L-100 Series
Бренд: Hammond Organ Страницы: 87
WalkLAB HP9000 Operation Manual preview
HP9000
Бренд: WalkLAB Страницы: 16
DGH DGH 55B Operator'S Manual preview
DGH 55B
Бренд: DGH Страницы: 87
Orange Electronic P451 Manual preview
P451
Бренд: Orange Electronic Страницы: 21
LaserLiner VideoPocket HD Manual preview
VideoPocket HD
Бренд: LaserLiner Страницы: 52
Veris H704-42 Installation Manual preview
H704-42
Бренд: Veris Страницы: 8
Magene P325 CS Quick Start Manual preview
P325 CS
Бренд: Magene Страницы: 80
Olimpus IPLEX RT Operation Manual preview
IPLEX RT
Бренд: Olimpus Страницы: 12
Nidec-Shimpo FGE-0.5XY Operation Manual preview
FGE-0.5XY
Бренд: Nidec-Shimpo Страницы: 6
LOVATO ELECTRIC DMED302 Instruction Manual preview
DMED302
Бренд: LOVATO ELECTRIC Страницы: 10
e-sylife Gas Module Installation Manual preview
Gas Module
Бренд: e-sylife Страницы: 2
TA Instruments TGA55 Getting Started Manual preview
TGA55
Бренд: TA Instruments Страницы: 68
LaserLiner F090.122A Manual preview
F090.122A
Бренд: LaserLiner Страницы: 80
Harken RigTune Pro Manual preview
RigTune Pro
Бренд: Harken Страницы: 2
Huvitz CRK-8800 Service Manual preview
CRK-8800
Бренд: Huvitz Страницы: 58
Radians Innova EnviroMentor Field Finder User Instructions preview
EnviroMentor Field Finder
Бренд: Radians Innova Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды