manualshive.com logo in svg

Thermo Scientific ISQ 7000, Руководство по оборудованию


Поделиться
Скачать
background image

 

3 

Advanced Maintenance

Upgrading the ISQ 7000 System Software

Thermo Scientific

ISQ 7000 Hardware Manual

273

6. Click on the 

NIST Browser

 button to install the NIST MS Browser. This functionality is 

required to allow automatic searching of libraries from Xcalibur or layered applications. 
Install the NIST Browser according to the installation instructions. The NIST installer 
will automatically create the required folders for the browser and demo libraries. For best 
operation, do not change the default NIST Browser installation locations. 

7. This completes the Xcalibur Core Components installation for GC-MS. To install the 

GC and MS drivers that are needed for instrument operation, refer to the installation 
instructions that are provided with those discs.

8. Click

 Exit

 to leave the Xcalibur 4.0 Setup window.

Configuring LAN Adapter Inactivity Time

When the TRACE GC Ultra is equipped with a LAN CPU card, the inactivity timeout 
setting needs to be set to 30,000 ms to effectively maintain communication with the software, 
even in periods of heavy data processing. Depending on the serial number of your TRACE 
GC Ultra, the software tool used to manage the LAN CPU may vary. 

To configure the NPort Management Suite

1. Open the NPort Management Suite by selecting 

Start | All Programs | NPort 

Management Suite | Configurator

.

2. Click the magnifying glass button on the tool bar or click 

Locate Server

 from the menu 

to automatically search for the TRACE GC Ultra LAN adapter.

3. Double-click on the IP address for the TRACE GC Ultra to configure the adapter.

4. In the Configuration window, click the 

OP_mode

 tab and select the 

Change OP_mode

 

checkbox. Then click the 

More Settings

 button.

5. In the TCP Server window, set the Inactivity time field to 30,000 ms and click 

OK

.

6. Click 

OK

 again to upload these settings to the LAN adapter. When the settings have been 

uploaded successfully, you can close the NPort utility and proceed to the Instrument 
Configuration process for the TRACE GC Ultra.

To configure the Network Enabler

1. Open the Network Enabler application by selecting 

Start | All Programs | Network 

Enabler

.

2. Under Configuration, select 

Broadcast Search

.

Note  

The Xcalibur 4.0 Core Components for GC-MS disc also includes the validation 

certificate for the Xcalibur core, the release notes for Foundation and Xcalibur and folders 
containing the manuals for these products. This content can be explored from the 
Xcalibur 4.0 Setup window using the Browse CD and Validation Certificate buttons.

Содержание ISQ 7000



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ISQ 7000

AccuMASTER 7434 User Manual preview
7434
Бренд: AccuMASTER Страницы: 2
GE DigitalFlow GF868 Startup Manual preview
DigitalFlow GF868
Бренд: GE Страницы: 80
Xsens DOT Quick Setup Manual preview
DOT
Бренд: Xsens Страницы: 4
Eastron SDM120 Series Manual preview
SDM120 Series
Бренд: Eastron Страницы: 2
EASTERN INSTRUMENTS CentriFlow Quick Start Manual preview
CentriFlow
Бренд: EASTERN INSTRUMENTS Страницы: 3
Oldham MX15 Installation And Operating Instructions Manual preview
MX15
Бренд: Oldham Страницы: 22
Macherey-Nagel NANOCOLOR UV/VIS II Manual preview
NANOCOLOR UV/VIS II
Бренд: Macherey-Nagel Страницы: 99
Ralston Instruments LC10 Series Quick Start Manual preview
LC10 Series
Бренд: Ralston Instruments Страницы: 52
E Instruments E4500 Operating & Maintenance Manual preview
E4500
Бренд: E Instruments Страницы: 144
Velleman DVR8T3 Quick Installation Manual preview
DVR8T3
Бренд: Velleman Страницы: 107
Seben 69003 Instruction Manual preview
69003
Бренд: Seben Страницы: 16
CAS Corporation TW-100 Service Manual preview
TW-100
Бренд: CAS Corporation Страницы: 20
SANKO SWT-7200 II Instruction Manual preview
SWT-7200 II
Бренд: SANKO Страницы: 97
Staco Energy EMD Quick Manual preview
EMD
Бренд: Staco Energy Страницы: 2
Maico HY 5 Mounting Instructions And Directions For Use preview
HY 5
Бренд: Maico Страницы: 2
Hanna Instruments HI97730 Instruction Manual preview
HI97730
Бренд: Hanna Instruments Страницы: 28
Hanna Instruments HI 93723 Instruction Manual preview
HI 93723
Бренд: Hanna Instruments Страницы: 2
Badger Meter American AL-1000 Installation & Operation Manual preview
American AL-1000
Бренд: Badger Meter Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды