Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 194 / 442

Advanced Maintenance

Replacing Components of the Analyzer

166

ISQ 7000 Hardware Manual

Thermo Scientific

7. Power on the ISQ 7000 mass spectrometer.

8. If the GC is powered off, power it on and make sure vacuum compensation is on for the

carrier gas flowing into the mass spectrometer.

WARNING FIRE HAZARD:

If you are using hydrogen, do NOT reach over the top of the

instrument to power it on. Instead, reach around the right side or go to the back of the
instrument and flip up the power switch.

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды