Thermo Scientific ISQ 7000 Скачать руководство пользователя

Страница: 379 / 442

Advanced Maintenance

Replacing the Power Supplies

Thermo Scientific

ISQ 7000 Hardware Manual

351

6. Pull the dynode power supply straight up and away from the distribution board on the

bottom of the chassis.

7. Replace the dynode/multiplier power supply and install it by aligning its connector with

the connector on the distribution board beneath it. It will drop into the slot when it is in
the right position.

8. Push the power supply down into the connector.

9. Reattach the screws holding the dynode and multiplier power supply in place.

Figure 392.

Replacing the Dynode/Multiplier Power Supply

Figure 393.

Reinstalling the Dynode/Multiplier Power Supply

Connector

Bottom
Screw

Back
Screws

Dynode/Multiplier
Power Supply

Содержание ISQ 7000



























































































































































































































































































































































































































































Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды

Thermo Scientific ISQ 7000, Руководство по оборудованию

Результаты поиска

Содержание ISQ 7000

Отзывы:

Похожие инструкции для ISQ 7000

Бренды по названию

Популярные бренды