Novexx Solutions ALX 92x, Service Manual

Page: 544 / 824

1. Only 64-xx dispenser with 4“ printhead 2. Only if SYSTEM PARAMETER > Ribbon autoecon. = „On“, „On Turbo“ or „Thermal/headlift“ 3. Only with 8-Dot-Emulation 4. Only with 64-08 5. Only with rewinder option 6. Only with cutter 7. Only
with USI interface 8. Only if SYSTEM PARAMETER > Gap detect. mode = Autom. feed back 9. Only with at least one data block stored in the flash memory 10. Only if SYSTEM PARAMETER > Print Interpret. = „ZPL Emulation“ 11. Only with I/
O board 12. Only if PRINT PARAMETERS > Punch mode = Manual 13. Only in production mode 14. Only with 64-xx dispenser 15. Only if SYSTEM PARAMETER > Autom. dot check = Continuous 16. For details read parameter description 17.
Only with 64-04/05/06 18. Only with installed RFID option 19. Only if DP INTERFACE > Interface type = USI Applicator 20. Only with SYSTEM PARAMETER > Dispensing edge = „User defined“ 21. Not with 64-xx dispenser 22. Only with an
activated RFID option 24. With connected remote display only 25. With Applicator Interface only 26. Only OLV option activated 27. Depends on the applicator type 28. Only if INTERFACE PARA > NETWORK PARAM. > WEB server = „On“ 29.
Availability depends on device conf. 30. Only with a CF card inserted 31. Only with a WLAN CF card inserted 32. Only if INTERFACE PARA > NETWORK PARAM. > Time client = „On“ 33. Only if SYSTEM PARAMETER > Periph. device = „Tear-
off edge“ 34. Only if SYSTEM PARAMETER > Periph. device = „Dispenser“ 35. Only if DISPENSER PARA > Transport mode = „Dual motors“ 36. Only if DISPENSER PARA > Speed Adaption = „On“ 37. Only if DISPENSER PARA > Multi label
mode = „x labels/start“ 38. Only if DISPENSER PARA > Multi label mode = „3 labels/start“ 39. Only PEM 39. Only if CPU board index is -06 or lower
05/16 Rev. 03 USER- / SERVICE MANUAL Info-Printouts & Parameters
64-xx – DPM – PEM – ALX 92x – ALX 73x (PMA)
22
ALX
73
x (P
MA)
Pa
ra
m
et
er
s
ALX 73x (PMA) all parameters
PRINT INFO PRINT PARAMETERS INTERFACE PARA (INTERFACE PARA cont.) (INTERFACE PARA cont.) SYSTEM PARAMETER
Printer status Print speed > EASYPLUGINTERPR Parity WLAN SSID 31 Cover open error
Memory status Feed speed Interface Data synch. WLAN WEP 31 Foil end warning
Font status Material type Spooler mode Stop bits WLAN default key 31 Foil warn stop
Flashdata status 9 Material length Printer ID No. Frame error WLAN 64Bit key 1 31 Autom. dot check
Service status Material width Spooler size WLAN 64Bit key 2 31 Early dottest 15
Dottest endless Print direction Offline mode > CENTRONICS WLAN 64Bit key 3 31 Latest dottest 15
Dottest punched Punch offset Interface delay PnP function WLAN 64Bit key 4 31 Dottestarea from 15
Reference label Bar code Multip. WLAN 128Bit key 1 31 Dottestarea to 15
Tradit. imaging 13 > COM1 PORT > NETWORK PARAM. WLAN 128Bit key 2 31 Print Interpret.
UPC plain-copy Baud rate IP Addressassign WLAN 128Bit key 3 31 Character sets
EAN Readline No. of data bits IP Address WLAN 128Bit key 4 31 Character filter
EAN sep. lines Parity Net mask WLAN com quality 31 Light sens. type
Rotated Barcodes Stop bits Gateway address WLAN signal lev. 31 Head-sensor dist. 13
X – print offset Data synch. Port address Ribbon autoecon.
Y – print offset Frame error Ethernet speed > OPTIONEN Ribbon eco. limit
Punch mode MAC address OLV option Feed mode
Punch level 12 > COM3 PORT 11 SNMP agent RFID option 18 Turn-on mode
Baud rate 11 SNMP password 13 StandAlone Input Error reprint
No. of data bits 11 FTP server #VW/I Interface EasyPlug errors
Parity 11 FTP password 13 Single job mode
Stop bits 11 WEB server > DRIVEASSIGNMENT Head resistance 13
Data synch. 11 WEB admin passw. 13 Drive C Temp. reduction
Serial Port Mode 11 WEB supervisor p. 13 Drive D Voltage offset
Frame error 11 WEB operator p. 13 Drive E 40 Expand Logo 3
Time client Drive F Miss. label tol.
> COM4 PORT Time server IP 32 Gap detect. mode
Baud rate Sync interval 32 Foil stretching 13
No. of data bits DHCP host name Head lift autom.
F
W
6.60