manualshive.com logo in svg

Analog Devices ADSP-BF59x Blackfin, Hardware Reference Manual, Page: 613 / 772

Share
Download
Analog Devices ADSP-BF59x Blackfin Hardware Reference Manual Download Page 613

ADSP-BF59x Blackfin Processor Hardware Reference

15-29 

 

Parallel Peripheral Interface

The 

FLD_SEL

 bit is used primarily in the active field only ITU-R 656 

mode. The 

FLD_SEL

 bit determines whether to transfer in only field 1 of 

each video frame, or both fields 1 and 2. Thus, it allows a savings in DMA 
bandwidth by transferring only every other field of active video.

The 

PORT_CFG[1:0]

 field is used to configure the operating mode of the 

PPI. It operates in conjunction with the 

PORT_DIR

 bit, which sets the 

direction of data transfer for the port. The 

XFR_TYPE[1:0]

 field is also 

used to configure operating mode and is discussed below. See 

Table 15-1 

on page 15-4

 for the possible operating modes for the PPI.

The 

XFR_TYPE[1:0]

 field configures the PPI for various modes of opera-

tion. Refer to 

Table 15-1 on page 15-4

 to see how 

XFR_TYPE[1:0]

 

interacts with other bits in 

PPI_CONTROL

 to determine the PPI operating 

mode.

The 

PORT_EN

 bit, when set, enables the PPI for operation. 

When configured as an input port, the PPI does not start data 
transfer after being enabled until the appropriate synchronization 
signals are received. If configured as an output port, transfer 
(including the appropriate synchronization signals) begins as soon 
as the frame syncs (timer units) are enabled, so all frame syncs must 
be configured before this happens. Refer to the section 

“Frame 

Synchronization in GP Modes” on page 15-19

 for more 

information.

PPI Status Register (PPI_STATUS)

The 

PPI_STATUS

 register, shown in 

Figure 15-14

, contains bits that pro-

vide information about the current operating state of the PPI. 

The 

ERR_DET

 bit is a sticky bit that denotes whether or not an error was 

detected in the ITU-R 656 control word preamble. The bit is valid only in 
ITU-R 656 modes. If 

ERR_DET

= 1, an error was detected in the preamble. 

If 

ERR_DET

= 0, no error was detected in the preamble.

Summary of Contents for ADSP-BF59x Blackfin





































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments