manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

System Units (Vol. 1 of 2)

CPU Subsystem

 

User’s Manual

2-48

V2.0, 2007-07

CPU, V2.0

 

2.7.2

Load-Store Pipeline Instructions

2.7.2.1

Address Arithmetic Timing

Each instruction is single issued.

Table 2-14

Address Arithmetic Instruction Timing

Instruction

Result 
Latency

Repeat 
Rate

Instruction

Result 
Latency

Repeat 
Rate

LS Arithmetic Instructions
ADD.A

1

1

GE.A

1

1

ADDIH.A

1

1

LT.A

1

1

ADDSC.A

1

1

NE.A

1

1

ADDSC.AT

1

1

NEZ.A

1

1

EQ.A

1

1

SUB.A

1

1

EQZ.A

1

1

NOP

1

1

Trap and Interrupt Instructions
DEBUG

–

1

TRAPSV

1)

1) Execution cycles when no TRAP is taken. The execution timing in the case of raising these TRAPs is the same

as other TRAPs such as SYSCALL.

–

1

DISABLE

–

1

TRAPV

3)

–

1

ENABLE

–

1

RSTV

–

1

Move Instructions
MFCR

1

1

MOV.A

1

1

MTCR

–

1

MOV.AA

1

1

MOVH.A

1

1

MOV.D

1

1

Sync Instructions
DSYNC

2)

2) Repeat rate assumes that no shadow register write-back is pending, other wise the repeat rate will depend

upon the time for all delayed memory operation to occur.

–

1

ISYNC

3)

3) Repeat rate assumes that code refetch takes a single cycle.

–

1

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

H3C WX5500H series User Configuration Manual preview
WX5500H series
Brand: H3C Pages: 57
Samson 3711 Mounting And Operating Instructions preview
3711
Brand: Samson Pages: 20
Jeep Liberty Instruction Sheet preview
Liberty
Brand: Jeep Pages: 32
Accel 300+ Installation Instructions Manual preview
300+
Brand: Accel Pages: 8
Kasco C10 Installation & Operation Manual preview
C10
Brand: Kasco Pages: 3
C Prox Ltd FP1 User Manual preview
FP1
Brand: C Prox Ltd Pages: 5
Federal Signal Corporation FC Description, Specifications, Installation, Operation, And Service Manual preview
FC
Brand: Federal Signal Corporation Pages: 34
Packard Bell Slim Remote Control Instruction preview
Slim Remote Control
Brand: Packard Bell Pages: 2
Unipower PCM500 Series Operating Manual preview
PCM500 Series
Brand: Unipower Pages: 24
Uniden UBC-RH96 Owner'S Manual preview
UBC-RH96
Brand: Uniden Pages: 28
UniFocus Time Clock Manager'S Manual preview
Time Clock
Brand: UniFocus Pages: 23
UniFocus Time Clock Wireless Connection Manual preview
Time Clock
Brand: UniFocus Pages: 6
Patron TOM 5 Information For Use preview
TOM 5
Brand: Patron Pages: 36
Allen-Bradley PowerFlex 755 IP00 Installation Instructions Manual preview
PowerFlex 755 IP00
Brand: Allen-Bradley Pages: 78
Paradox Esprit 727 Installation Instructions Manual preview
Esprit 727
Brand: Paradox Pages: 6
2gig Technologies Vario Installation Instructions Manual preview
Vario
Brand: 2gig Technologies Pages: 6
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Brand: W.E.ST. Pages: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Brand: Ltech Pages: 4

Brands by name

Popular brands

Load more brands