manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

Peripheral Units (Vol. 2 of 2)

Controller Area Network (MultiCAN) Controller

 

User’s Manual

22-75

V2.0, 2007-07

MultiCAN, V2.0

 

LECIE

2

rw

Last Error Code Interrupt Enable

LECIE enables the last error code interrupt of CAN 
node x. This interrupt is generated with each update of bit 
field NSRx.LEC with LEC > 0 (CAN protocol error).
0

B

Last error code interrupt is disabled.

1

B

Last error code interrupt is enabled.

Bit field NIPRx.LECINP selects the interrupt output line 
which becomes activated at this type of interrupt.

ALIE

3

rw

Alert Interrupt Enable

ALIE enables the alert interrupt of CAN node x. This 
interrupt is generated by any one of the following events:
•

A change of bit NSRx.BOFF

•

A change of bit NSRx.EWRN

•

A List Length Error, which also sets bit NSRx.LLE

•

A List Object Error, which also sets bit NSRx.LOE

•

A Bit INIT is set by hardware

0

B

Alert interrupt is disabled.

1

B

Alert interrupt is enabled.

Bit field NIPRx.ALINP selects the interrupt output line 
which becomes activated at this type of interrupt.

CANDIS

4

rw

CAN Disable

Setting this bit disables the CAN node. The CAN node 
first waits until it is bus-idle or bus-off. Then bit INIT is 
automatically set, and an alert interrupt is generated if bit 
ALIE is set.

CCE

6

rw

Configuration Change Enable

0

B

The Bit Timing Register, the Port Control Register, 
and the Error Counter Register can only be read. 
All attempts to modify them are ignored.

1

B

The Bit Timing Register, the Port Control Register, 
and the Error Counter Register may be read and 
written.

CALM

7

rw

CAN Analyze Mode

If this bit is set, then the CAN node operates in Analyze 
Mode. This means that messages may be received, but 
not transmitted. No acknowledge is sent on the CAN bus 
upon frame reception. Active-error flags are sent 

recessive

 instead of 

dominant

. The transmit line is 

continuously held at 

recessive

 (1) level.

Bit CALM can be written only while bit INIT is set.

Field

Bits

Type Description

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

Calsense ET2000e Programming Manual preview
ET2000e
Brand: Calsense Pages: 74
MacDon FM100 Installation Instructions Manual preview
FM100
Brand: MacDon Pages: 32
K&K M7500 Installation Instructions Manual preview
M7500
Brand: K&K Pages: 6
K'Nex Education 79018 User Manual preview
79018
Brand: K'Nex Education Pages: 56
VAT 670 Series Installation, Operating, & Maintenance Instructions preview
670 Series
Brand: VAT Pages: 39
Samson 3730-6 Mounting And Operating Instructions preview
3730-6
Brand: Samson Pages: 124
Samson TROVIS 5500 Operating Instructions Manual preview
TROVIS 5500
Brand: Samson Pages: 86
VAC V100 Troubleshooting Manual preview
V100
Brand: VAC Pages: 5
ZKTeco MA500 Installation Manual & User Manual preview
MA500
Brand: ZKTeco Pages: 20
ZKTeco ProFace X Installation Manual preview
ProFace X
Brand: ZKTeco Pages: 8
ZKTeco TF1600 ZKTeco Quick Start Manual preview
TF1600 ZKTeco
Brand: ZKTeco Pages: 10
ZKTeco SpeedFace-V3L User Manual preview
SpeedFace-V3L
Brand: ZKTeco Pages: 121
ZKTeco FaceDepot-7BL Quick Start Manual preview
FaceDepot-7BL
Brand: ZKTeco Pages: 12
ZKTeco C5S110 Installation And Connection Manual preview
C5S110
Brand: ZKTeco Pages: 6
ZiLOG Z8 Encore! XP Quick Start Manual preview
Z8 Encore! XP
Brand: ZiLOG Pages: 12
ZIMMERLI MESSTECHNIK LPS Series Operating Manual preview
LPS Series
Brand: ZIMMERLI MESSTECHNIK Pages: 12
H-Tronic TS 125 Manual preview
TS 125
Brand: H-Tronic Pages: 32
Eaton EZD Series User Manual preview
EZD Series
Brand: Eaton Pages: 448

Brands by name

Popular brands

Load more brands