manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

Peripheral Units (Vol. 2 of 2)

Micro Link Interface (MLI)

 

User’s Manual

23-75

V2.0, 2007-07

MLI, V2.0

 

23.4

MLI Kernel Registers

This section describes the kernel registers of the MLI modules. All MLI kernel register
names described in this section will be referenced in other parts of the TC1796 User’s
Manual by the module name prefix “MLI0_” for the MLI0 interface and “MLI1_” for the
MLI1 interface.

MLI Kernel Register Overview

Figure 23-50 MLI Kernel Registers

All registers can be accessed with 8-bit, 16-bit or 32-bit write or read operations.
Accesses to address locations inside the MLI address range not targeting the indicated
registers are not allowed. The complete and detailed address map of the of the MLI
modules is described in 

Table 18-30

 on 

Page 18-97

 of the TC1796 User’s Manual

System Units part (Volume 1).

TPxBAR

MCA06320_mod

TPxAOFR
TCBAR

RPxBAR
RADRR

FDR

TSTATR
TPxSTATR
TCDMR
TRSTATR

TCR

RPxSTATR

SCR

TIER
TISR
TINPR

RIER
RISR
RINPR

GINTR

OICR

TPxDATAR
TDRAR

RDATAR

AER
ARR

x = 0-3 (Number of pipes)

General Module 

Registers

General Status /

Control Registers

Access Protection

Registers

Transmission Status/

Control Registers

Transmission Data /

Address Registers

Transmitter Interrupt 

Registers

Receiver Status /

Control Registers

Receiver Data /

Address Registers

Receiver Interrupt 

Registers

RCR

ID

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

S&C 5800 Series Operating Instructions Manual preview
5800 Series
Brand: S&C Pages: 40
S&C 5800 Series Troubleshooting Manual preview
5800 Series
Brand: S&C Pages: 34
Vasco RF User And Installation Manual preview
RF
Brand: Vasco Pages: 32
Abra AK-10 User Manual preview
AK-10
Brand: Abra Pages: 16
SAI Connect Operation Manual preview
Connect
Brand: SAI Pages: 16
Hable One Starting Manual preview
One
Brand: Hable Pages: 3
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Danfoss VLT DriveMotor FCP 106 Installation Instructions preview
VLT DriveMotor FCP 106
Brand: Danfoss Pages: 4
Olimpia splendid SHERPA MONOBLOC B0812 Owner'S Manual preview
SHERPA MONOBLOC B0812
Brand: Olimpia splendid Pages: 44
Olimpia splendid B1012 Installation And Maintenance Instruction preview
B1012
Brand: Olimpia splendid Pages: 44
Olimpia splendid Bi2 B0772 Instructions Manual preview
Bi2 B0772
Brand: Olimpia splendid Pages: 16
Saab R5 SUPREME AIS Short Instruction preview
R5 SUPREME AIS
Brand: Saab Pages: 4
B&G ZEUS S Detailed App Manual preview
ZEUS S
Brand: B&G Pages: 19
LST Extinguishing Control Panel BC06-2EXT Brochure & Specs preview
Extinguishing Control Panel BC06-2EXT
Brand: LST Pages: 4
Viking VC-1000 Technical Practice preview
VC-1000
Brand: Viking Pages: 4
Vag GA Figure 220-D Installation, Operation And Maintenance Manual preview
GA Figure 220-D
Brand: Vag Pages: 6
Radionics D9024 Manual preview
D9024
Brand: Radionics Pages: 18
Renogy Rover 100A Manual preview
Rover 100A
Brand: Renogy Pages: 36

Brands by name

Popular brands

Load more brands