manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

Share
Download
Infineon Technologies TC1796 User Manual Download Page 2104

TC1796

Peripheral Units (Vol. 2 of 2)

Fast Analog-to-Digital Converter (FADC)

 

User’s Manual

26-53

V2.0, 2007-07

FADC, V2.0

 

AC

[26:24]

rh

Addition Count

This bit field indicates the number of additions of filter 
input values with remain to be executed before the 
next intermediate result register transfer occurs. AC 
is loaded with the value of FCRn.ADDL for a new 
addition sequence.
CR is cleared when writing GCR.RSTFn = 1.

MAVS

[29:28]

rh

Moving Average State

This bit field indicates how many intermediate 
register transfers remain to be executed for the 
generation of the next final result.
MAVS = 0 indicates the end of a filter calculation 
operation. Since the filter calculation is executed 
very fast in comparison to a conversion, MAVS > 0 
can be interpreted only as a kind of calculation busy 
flag. Therefore, it is recommended to read a valid 
filter result from register FRRn only when the 
corresponding interrupt request flag CRSR.IRQFn is 
set.
MAVS is cleared when writing GCR.RSTFn = 1.

0

[23:18], 
27, 
[31:30]

r

Reserved

Read as 0.

Field

Bits

Type Description

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands