manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

System Units (Vol. 1 of 2)

Program Memory Unit

 

User’s Manual

7-36

V2.0, 2007-07

PMU, V2.0

 

7.2.9

Flash Interrupt Generation and Control

One interrupt request can be issued by the Flash module. The related interrupt control
register is located in the DMA controller.
The Flash interrupt can be issued when any of the following events occur:
•

End-of-busy: programming or erase operation of Flash bank finished

•

Command sequence error

•

Protection error

•

Single-bit error in PFLASH

•

Single-bit error in DFLASH

•

Double-bit error in PFLASH

•

Double-bit error in DFLASH

The source of the Flash interrupt is indicated in the Flash Status Register FSR by the
corresponding busy and error flags. Every interrupt source is disabled after reset, and
can be enabled individually via dedicated enable bits in the Flash Configuration Register
FCON.
The end-of-busy interrupt becomes active whenever a programming or erasing
operation is finished. At this event, one of the three FSR busy flags PBUSY, D0BUSY,
or D1BUSY is cleared from 1 to 0. End-of-busy interrupts are enabled by setting the
FCON.EOBM bit.
The error flags in the Flash Status Register are controlled independently of the interrupt
configuration as defined in the FCON register. Thus, they may be polled without interrupt
support. When set, an error flag has to be cleared by the user with the Clear Status
command. All error flags are also cleared with any reset.
Errors, which are caused by a reset during program or erase operation, are not indicate,
but its detection is supported via the PROG and ERASE flags in the Flash Status
Register FSR. These two flags are cleared only with a power-on reset. Therefore, it is
possible to detect an aborted Flash operation, if after every terminated Flash operation
these flags are immediately cleared by the user with the Clear Status command, and if
these flags are checked with every user-boot after reset (all except power-on reset).

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

Paratec TE Series User Manual preview
TE Series
Brand: Paratec Pages: 8
J+J S2 Handbook preview
S2
Brand: J+J Pages: 33
Lawler 61 Series Installation & Maintenance Manual preview
61 Series
Brand: Lawler Pages: 4
Hama 11412 Operating Instruction preview
11412
Brand: Hama Pages: 46
Galcon 61 Series Installation And Operating Instructions Manual preview
61 Series
Brand: Galcon Pages: 35
Febco Master Series Installation Instructions Manual preview
Master Series
Brand: Febco Pages: 12
GameSir G4s User Manual preview
G4s
Brand: GameSir Pages: 8
Game ready 550450 User Manual preview
550450
Brand: Game ready Pages: 21
VAMP 259 Operation And Configuration Instructions preview
259
Brand: VAMP Pages: 304
Tactical TTC Instruction Manual preview
TTC
Brand: Tactical Pages: 8
K'Nex Education 79018 User Manual preview
79018
Brand: K'Nex Education Pages: 56
Universal Remote Genesis MX-900 Manual preview
Genesis MX-900
Brand: Universal Remote Pages: 20
Partizan PAB-FC2 Quick Start Manual preview
PAB-FC2
Brand: Partizan Pages: 7
Phytec phyCORE-MCF548x Hardware Manual preview
phyCORE-MCF548x
Brand: Phytec Pages: 104
I-Tork PDS Series Installation & Operation Manual preview
PDS Series
Brand: I-Tork Pages: 15
MGC RAXN-LCD Installation And Wiring Manual preview
RAXN-LCD
Brand: MGC Pages: 16
Multi-Clean 421914 Quick Start Manual preview
421914
Brand: Multi-Clean Pages: 4
Primo Water PRWF-80455 Instructions Manual preview
PRWF-80455
Brand: Primo Water Pages: 10

Brands by name

Popular brands

Load more brands