Infineon Technologies TC1796 User Manual Download Page 866

Page: 866 / 2150

TC1796

System Units (Vol. 1 of 2)

LMB External Bus Unit

User’s Manual

13-88

V2.0, 2007-07

EBU, V2.0

FDBKEN

Burst Flash Clock Feedback Enable

BFCLK feedback not used. In this case, bit field
DTALTNCY must be set to 0000

Incoming data and control signals (from the
Burst Flash device) are re-synchronized to the
BFCLKI input.

DTALTNCY

[15:12] rw

Latency Cycle Control

This bit field determines the number of additional
LMBCLK cycles of latency to be used when sampling
inputs from the Burst Flash devices.

FETBLEN1

[19:16] rw

Fetch Burst Length for Burst Flash Type 1

This bit field determines the maximum number of
burst data cycles which are executed by the EBU
during a Burst Flash Type 1 burst access.
000

1 data access (default after reset).

001

2 data accesses.

010

4 data accesses.

011

8 data accesses.

1XX

Reserved.

FBBMSEL1

Flash Burst Buffer Mode Select for Burst Flash
Type 1

Continuous mode.

Flash burst buffer length is defined by the value
of FETBLEN1 (default after reset).

WAITFUNC1

Function of WAIT input for Burst Flash Type 1

The WAIT input operates as a wait data bus
function on bursts (default after reset).

The WAIT input operates as a terminate burst
function.

EBSE1

Early Burst Signal Enable for Burst Flash Type 1

Outputs ADV and BAA are delayed by 1/2
LMBCLK period (default after reset).

Outputs ADV and BAA are not delayed.

(see

Page 13-73

)

Field

Bits

Type Description

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TC1796

Reviews:

Brands by name

Popular brands

Infineon Technologies TC1796, User Manual

Search results

Summary of Contents for TC1796

Reviews:

Brands by name

Popular brands