manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

Share
Download
Infineon Technologies TC1796 User Manual Download Page 1839

TC1796

Peripheral Units (Vol. 2 of 2)

General Purpose Timer Array (GPTA)

 

User’s Manual

24-184

V2.0, 2007-07

GPTA, V2.0

 

BYP

6

rw

Bypass

0

B

M0O/M1O lines are affected either by M0I/M1I 
lines or by OCM0/OCM1 bits.

1

B

M0O/M1O lines are affected only by M0I/M1I 
lines.

This bit is cleared if mode is switched to Timer Mode. 
OCM2 must be set in any case to enable reaction on 
M0I/M1I change.

EOA

7

rwh

Enable On Action

0

B

LTCk is enabled for local events.

1

B

LTCk is disabled for local events. On an event on 
the communication link via M0I/M1I lines, EOA 
will be cleared and local events will be enabled.

EOA is bit protected (see 

Section 24.3.2

). EOA is 

cleared if mode is switched to Timer Mode.

ILM

8

rw

Input Line Mode

0

B

Input line is operating in Edge Sensitive Mode.

1

B

Input line is operating in Level Sensitive Mode.

In case of full speed GPTA module clock selection as 
input clock, Level Sensitive Mode must be selected. In 
this case the Edge Sensitive Mode will not produce any 
event.

SLL

9

rh

Capture & Compare Mode: Select Line Level

0

B

Current state of select input SI is 0.

1

B

Current state of select input SI is 1.

CEN

10

rh

Cell Enable

0

B

LTCk is currently disabled for local events.

1

B

LTCk is currently enabled for local events.

OCM

[13:11] rw

Output Control Mode Select

X00

B

Current state of LTCkOUT output line is hold.

X01

B

Current state of LTCkOUT output line is toggled.

X10

B

LTCkOUT output line is forced to 0.

X11

B

LTCkOUT output line is forced to 1.

0XX

B

LTCkOUT output line state is set by an internal 
LTCk event only.

1XX

B

LTCkOUT output line state is affected by an 
internal LTCk event and/or by an operation 
occurred in an adjacent LTCk cell (reported by 
M1I/M0I interface lines).

Field

Bits

Type Description

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands