manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

System Units (Vol. 1 of 2)

Interrupt System

 

User’s Manual

14-25

V2.0, 2007-07

Interrupt, V2.0

 

14.10

Non-Maskable Interrupt

Although called an interrupt, the Non-Maskable Interrupt (NMI) is actually serviced as a
trap, since it is not interruptible and does not follow the standards for regular interrupts.
In the TC1796, four different events can generate an NMI trap:
•

A transition on the NMI input pin

•

An error or wake-up signal from the Watchdog Timer

•

The PLL becomes unlocked

•

The occurrence of an SRAM parity error in an on-chip memory block

The type of NMI trap is indicated in the NMI Status Register (NMISR).

14.10.1

External NMI Input

An external NMI event is generated when a one-to-zero transition is detected at the
external NMI input pin. NMISR.NMIEXT is set in this case. The NMI pin is sampled at the
system clock frequency. A transition is recognized when one sample shows a 1 and the
next sample shows a 0. Subsequent 0-samples or a 0-to-1 transition do not trigger any
action.
NMI is equipped with a noise suppression filter which suppresses glitches below 10 ns
pulse width. NMI pulses with a width above 100 ns are safely recognized as a valid
signal. The noise suppression filter is switched-off when pin BYPASS = 1.

14.10.2

Phase-Locked Loop NMI

The PLL clock generation unit sets the NMIPLL flag when it detects a loss in the
synchronization with the external oscillator clock input. This condition means that the
PLL clock frequency is no longer stable, and that the PLL will now decrease to its VCO
clock base frequency.

14.10.3

Watchdog Timer NMI

The Watchdog Timer sets the NMIWDT flag for two conditions:
•

A Watchdog Timer error has occurred

•

Bit 15 of the Watchdog Timer is set while the CPU is in idle mode

A Watchdog Timer error can produce an NMI event because:
•

Access to register WDT_CON0 was attempted improperly, or

•

The Watchdog Timer overflowed either in Time-Out Mode or in Normal Watchdog
Timer Mode.

When the CPU is in Idle Mode and the Watchdog Timer is not disabled, an increment of
the Watchdog Timer counter from 7FFF

H

 to 8000

H

 (that is, when bit 15 of the timer is set

to 1) sets the NMIWDT bit to wake up the CPU.

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

IBM ServeRAID M5014 User Manual preview
ServeRAID M5014
Brand: IBM Pages: 106
C.Nord GSM Operation Manual preview
GSM
Brand: C.Nord Pages: 100
3Com CoreBuilder 9000 Getting Started Manual preview
CoreBuilder 9000
Brand: 3Com Pages: 78
CALEFFI 145 Series Installation And Commissioning Manual preview
145 Series
Brand: CALEFFI Pages: 12
CALEFFI QuickSetter+ 132 Series User Manual preview
QuickSetter+ 132 Series
Brand: CALEFFI Pages: 5
Daikin Madoka User Manual preview
Madoka
Brand: Daikin Pages: 2
Daikin BRC7E530W8 Operation Manual preview
BRC7E530W8
Brand: Daikin Pages: 12
Daikin BRC1H81K Installation And Operation Manual preview
BRC1H81K
Brand: Daikin Pages: 12
Daikin BRC1H71W Operation Manual preview
BRC1H71W
Brand: Daikin Pages: 46
Daikin BRC1D71 Operation Manual preview
BRC1D71
Brand: Daikin Pages: 21
Daikin BRC1D517 Operation Manual preview
BRC1D517
Brand: Daikin Pages: 20
UCS CAT Quick Start Manual preview
CAT
Brand: UCS Pages: 4
VAT 264 Series Installation, Operating, & Maintenance Instructions preview
264 Series
Brand: VAT Pages: 26
Danfoss ChangeOver6 Operating Manual preview
ChangeOver6
Brand: Danfoss Pages: 2
Dejero EM9191 Hardware Integration Manual preview
EM9191
Brand: Dejero Pages: 24
WINDY NATION CHC-LCD-30FM User Manual preview
CHC-LCD-30FM
Brand: WINDY NATION Pages: 16
Kaba Mauer 82132 Mounting Instructions preview
82132
Brand: Kaba Mauer Pages: 10
Elotech R 1300 Description And Operating Manual preview
R 1300
Brand: Elotech Pages: 20

Brands by name

Popular brands

Load more brands