manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

Share
Download
Infineon Technologies TC1796 User Manual Download Page 936

TC1796

System Units (Vol. 1 of 2)

System Timer

 

User’s Manual

15-19

V2.0, 2007-07

STM, V2.0

 

CMP0OS

2

rw

Compare Register CMP0 Interrupt Output Selection

This bit determines the interrupt output that is activated 
on a compare match event of compare register CMP0.
0

B

Interrupt output STMIR0 selected

1

B

Interrupt output STMIR1 selected

CMP1EN

4

rw

Compare Register CMP1 Interrupt Enable Control

This bit enables the compare match interrupt with 
compare register CMP1.
0

B

Interrupt on compare match with CMP1 disabled

1

B

Interrupt on compare match with CMP1 enabled

CMP1IR

5

rh

Compare Register CMP1 Interrupt Request Flag

This bit indicates whether or not a compare match 
interrupt request of compare register CMP1 is pending. 
CMP1IR must be cleared by software.
0

B

A compare match interrupt has not been detected 
since the bit has been cleared for the last time.

1

B

A compare match interrupt has been detected.

CMPIR1 must be cleared by software and can be set by 
software, too (see CMPISRR register). After an STM 
reset CMP1IR is immediately set as the result of a 
compare match event with the reset values of the STM 
and the compare register CMP1.

CMP1OS

6

rw

Compare Register CMP1 Interrupt Output Selection

This bit determines the interrupt output that is activated 
on a compare match event of compare register CMP1.
0

B

Interrupt output STMIR0 selected

1

B

Interrupt output STMIR1 selected

0

3, 
[31:7]

r

Reserved

Read as 0; should be written with 0.

Field

Bits

Type Description

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands