manualshive.com logo in svg

Infineon Technologies TC1796, User Manual, Page: 2014 / 2150

Share
Download
Infineon Technologies TC1796 User Manual Download Page 2014

TC1796

Peripheral Units (Vol. 2 of 2)

Analog-to-Digital Converter (ADC)

 

User’s Manual

25-83

V2.0, 2007-07

ADC, V2.0

 

PCDIS

27

rw

Post Calibration Disable

This bit disables the automatic post calibration. Post 
calibration takes place after each conversion. The 
next conversion is started after the end of the post 
calibration. If post calibration, the actual conversion 
length increases by two 

f

ANA

 analog clock cycles due 

to the post calibration).
0

B

The post calibration is enabled.

1

B

The post calibration is disabled.

CPR

28

rw

Clear of Pending Conversion Requests in Parallel 
Sources by Arbiter

Bit CPR determines whether or not all pending 
conversion requests for an A/D channel, indicated by 
STAT.CHNRCC, are cancelled by the arbiter, when 
the conversion for this channel has been started.
0

B

The individual clear by arbiter is enabled. Only 
the conversion request of channel n of the 
winning source is cleared when a conversion of 
channel n is started.

1

B

The global clear by arbiter is enabled. All 
conversion requests for channel n are cleared 
in parallel sources if a conversion of channel n 
is started.

SRTEST

31

rw

Service Request Test Mode

This bit is used to set a source service request flag 
under software control.

0

[14:10],
[26:20],
[30:29]

r

Reserved

Read as 0; should be written with 0.

Field

Bits

Type Description

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments