Infineon Technologies TC1796 User Manual Download Page 723

Page: 723 / 2150

TC1796

System Units (Vol. 1 of 2)

Direct Memory Access Controller

User’s Manual

12-59

V2.0, 2007-07

DMA, V2.0

The Error Status Register indicates if the DMA controller couldn’t answer to a request
because the previous request was not terminated (see

Section 12.1.4.4

). It indicates

also the FPI Bus accesses that have been terminated with errors.

DMA_ERRSR
DMA Error Status Register

(024

)

Reset Value: 0000 0000

MLI

LEC

ME1

MLI

LEC

ME0

FPI1

FPI0

ME1
DER

ME1
SER

ME0

DER

ME0
SER

TRL

Field

Bits

Type Description

TRL0x
(x = 0-7)

Transaction/Transfer Request Lost of
DMA Channel 0x

No request lost event has been detected for DMA
channel 0x.

A new DMA request was detected while
TRSR.CH0x=1 (request lost event).

This bit is cleared by software when writing a 1 to
CLRE.CTL0x, or by a DMA channel reset (writing
CHRSTR.CH0x = 1).

TRL1x
(x = 0-7)

8+x

Transaction/Transfer Request Lost of
DMA Channel 1x

No request lost event has been detected for DMA
channel 1x.

A new DMA request was detected while
TRSR.CH1x=1 (request lost event).

This bit is cleared by software when writing a 1 to
CLRE.CTL1x, or by a DMA channel reset (writing
CHRSTR.CH1x = 1).

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for TC1796

Reviews:

Related manuals for TC1796

Brands by name

Popular brands

Infineon Technologies TC1796, User Manual

Search results

Summary of Contents for TC1796

Reviews:

Related manuals for TC1796

Brands by name

Popular brands