manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

The User Manual for the Infineon Technologies TC1796 is available for free download on our website. This comprehensive manual provides detailed instructions and information on operating and optimizing the TC1796 product. Dive into the features and functionalities of this advanced technology by downloading the manual from manualshive.com.

Share
Download
background image

TC1796

System Units (Vol. 1 of 2)

Direct Memory Access Controller

 

User’s Manual

12-15

V2.0, 2007-07

DMA, V2.0

 

Combined Software/Hardware-controlled Mode

Figure 12-9

 shows how software- and hardware-controlled modes can be combined. In

the example, the first DMA transfer is triggered by software when setting
STREQ.SCHmn. Hardware requests are still disabled. After hardware requests have
been enabled by setting HTREQ.ECHmn, subsequent DMA transfers are triggered now
by hardware request coming from the CHmn_REQ line.
In the example, DMA channel mn operates in Single Mode (CHCRmn.CHMODE = 0). In
this mode, TRSR.HTREmn becomes cleared by hardware when CHSRmn.TCOUNT
reaches 0 at the end of the DMA transaction.

Figure 12-9 Transaction Start by Software, Continuation by Hardware

12.1.4.4 Error Conditions

The source move error flag ERRSR.FPI0SER indicates an FPI Bus error on bus 0 (SPB)
that occurred during a source move (read) of a DMA transaction. The destination move
error flag ERRSR.FPI0DER indicates an FPI Bus error on bus 0 (SPB) that occurred
during a destination move (write) of a DMA transaction.
The transaction lost error flag ERRSR.TRLmn indicates if a DMA request for a DMA
channel mn has been lost.
In the case of a read error, the write action is not executed, but the destination address
is updated.

MCT05688

tc = initial transfer count

TR0

TRn-1

TRn

TR1

tc-1

tc

0

0

2

1

TRSR.CHmn

Writing
STREQ.SCHmn=1

Writing
HTREQ.ECHmn=1

TRSR.HTREmn

CHmn_REQ

DMA Transfer mn

CHSRmn.
TCOUNT

INT
(triggered at the end
of a transaction with
IRDV = 0)

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for TC1796

Radarcan R-200 User Manual preview
R-200
Brand: Radarcan Pages: 40
Yudian AI Series Operation Instruction Manual preview
AI Series
Brand: Yudian Pages: 26
Vanderbilt SPCN310 Installation Instruction preview
SPCN310
Brand: Vanderbilt Pages: 2
WAREMA LONMSE 2M230I Operating And Installation Instructions preview
LONMSE 2M230I
Brand: WAREMA Pages: 4
Yamaha RCX340 Service Information preview
RCX340
Brand: Yamaha Pages: 5
Yamaha ACD1 Owner'S Manual preview
ACD1
Brand: Yamaha Pages: 20
Yamaha DCP4S-EU Owner'S Manual preview
DCP4S-EU
Brand: Yamaha Pages: 2
Mitsubishi A1SJ71E71N-B2 User Manual preview
A1SJ71E71N-B2
Brand: Mitsubishi Pages: 30
Objective Imaging OASIS-4i Installation Manual preview
OASIS-4i
Brand: Objective Imaging Pages: 11
knorr-baby PIQUETTO Manual preview
PIQUETTO
Brand: knorr-baby Pages: 44
ICP DAS USA M-7067D Quick Start Manual preview
M-7067D
Brand: ICP DAS USA Pages: 6
FADAL VH5C Manual preview
VH5C
Brand: FADAL Pages: 2
t.a.c. I/A MicroNet MN-S Series General Instructions Manual preview
I/A MicroNet MN-S Series
Brand: t.a.c. Pages: 20
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
Ascon tecnologic vP4 Installation Manual preview
vP4
Brand: Ascon tecnologic Pages: 4
Phylrich 34Therm-001 Installation & Owner'S Manual preview
34Therm-001
Brand: Phylrich Pages: 3
Espressif Systems ESP32-DevKitC Getting Started Manual preview
ESP32-DevKitC
Brand: Espressif Systems Pages: 11
Velleman CHLSC2 User Manual preview
CHLSC2
Brand: Velleman Pages: 22

Brands by name

Popular brands

Load more brands