manualshive.com logo in svg

Infineon Technologies TC1796, User Manual

Share
Download
Infineon Technologies TC1796 User Manual Download Page 971

TC1796

System Units (Vol. 1 of 2)

Watchdog Timer

 

User’s Manual

16-33

V2.0, 2007-07

WDT, V2.0

 

WDTOE

1

rh

Watchdog Overflow Error Status Flag

0

B

No Watchdog overflow error.

1

B

A Watchdog overflow error has occurred.

This bit is set by hardware when the WDT overflows 
from FFFF

H

 to 0000

H

. This bit is only cleared when:

•

A power-on, hardware, or software reset occurs;

•

WDT_CON0.ENDINIT is set to 1 during a Valid
Modify Access.

However, it is not possible to cleared this bit if the 
WDT is in Prewarning Mode, indicated by 
WDT_SR.WDTPR = 1.

WDTIS

2

rh

Watchdog Input Clock Status Flag

0

B

WDT input clock is 

f

SYS

/16384

(default after reset).

1

B

WDT input clock is 

f

SYS

/256.

This bit is updated with the state of bit 
WDT_CON1.WDTIR after WDT_CON0.ENDINIT is 
written with 1 during a Valid Modify Access to register 
WDT_CON0.

WDTDS

3

rh

Watchdog Enable/Disable Status Flag

0

B

WDT is enabled (default after reset).

1

B

WDT is disabled.

This bit is updated with the state of bit 
WDT_CON1.WDTDR after WDT_CON0.ENDINIT is 
written with 1 during a Valid Modify Access to register 
WDT_CON0.

WDTTO

4

rh

Watchdog Time-Out Mode Flag

0

B

Normal mode.

1

B

The Watchdog is operating in Time-Out Mode 
(default after reset).

This bit is set to 1 when Time-Out Mode is entered, 
automatically after a reset and after every Password 
Access to register WDT_CON0. It is automatically 
cleared by hardware when Time-Out Mode is properly 
terminated through a Valid Modify Access to 
WDT_CON0. It is left set when a Watchdog error 
occurs during Time-Out Mode, and Prewarning Mode 
is entered.

Field

Bits

Type Description

Summary of Contents for TC1796







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands