Freescale Semiconductor PowerPC e500 Core Reference Manual Download Page 283 | Manualshive

Page: 283 / 548

background image

Interrupts and Exceptions

PowerPC e500 Core Family Reference Manual, Rev. 1

Freescale Semiconductor

5-31

5.7.15 EIS-Defined Interrupts

The interrupts in this section are defined by the EIS and supported by the e500.

NOTE

The SPE APU and embedded floating-point APU functionality is
implemented in all PowerQUICC III devices. However, these
instructions will not be supported in devices subsequent to
PowerQUICC III. Freescale Semiconductor strongly recommends
that use of these instructions be confined to libraries and device
drivers. Customer software that uses SPE or embedded floating-point
APU instructions at the assembly level or that uses SPE intrinsics will
require rewriting for upward compatibility with next-generation
PowerQUICC devices.

Freescale Semiconductor offers a libmoto_e500 library that uses SPE
instructions. Freescale will also provide libraries to support
next-generation PowerQUICC devices.

5.7.15.1 SPE/Embedded Floating-Point APU Unavailable Interrupt

As defined by the EIS, an SPE APU unavailable interrupt is taken if MSR[SPE] is cleared and an
SPE, embedded scalar double-precision (e500v2 only), or embedded vector single-precision
floating-point instruction is executed. It is not used by the embedded scalar single-precision
floating-point APU. However, on the e500v1, MSR[SPE] affects the SPE and both the vector and
scalar single-precision floating-point APUs.

On the e500v2, MSR[SPE] affects only instructions that affect the upper and lower portions of the
64-bit GPRs, that is, instructions defined by the SPE, the vector single-precision floating-point
APU, and the double-precision floating-point APUs. It does not affect scalar single-precision
floating-point APU instructions.

When an SPE unavailable interrupt occurs, the processor suppresses execution of the instruction
causing the interrupt. The SRR0, SRR1, MSR, and ESR registers are modified as shown in

Table 5-29

.

Instruction execution resumes at address IVPR[32–47] || IVOR32[48–59] || 0b0000.

Table 5-29. SPE/Embedded Floating-Point APU Unavailable Interrupt Register Settings

Register

Setting

SRR0

Set to the effective address of the instruction causing the interrupt.

SRR1

Set to the MSR contents at the time of the interrupt.

MSR

CE, ME, and DE are unchanged. All other bits are cleared.

ESR

SPE (bit 24) is set. All other ESR bits are cleared.

«
...
281
282
283
284
285
...
»

Summary of Contents for PowerPC e500 Core





































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerPC e500 Core

Brand: ASROCK Pages: 5

DS-5116HFI Series

Brand: HIKVISION Pages: 22

Brand: Fastfame Pages: 41

i.MX 8M Mini SODIMM SOM

Brand: iWave Pages: 16

Brand: OLIMEX Pages: 26

CS631-C246/Q370

Brand: DFI Pages: 79

Brand: Supero Pages: 89

Brand: Acorp Pages: 54

Brand: WinSystems Pages: 16

Brand: Intel Pages: 73

Brand: MSI Pages: 98

Brand: ComNav Technology Pages: 28

Brand: Asus Pages: 84

Brand: Asus Pages: 49

Brand: GE Pages: 4

Brand: GE Pages: 81

Brand: GE Pages: 84

Brand: GE Pages: 93

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands