Freescale Semiconductor PowerPC e500 Core Reference Manual Download Page 319 | Manualshive

Page: 319 / 548

background image

Debug Support

PowerPC e500 Core Family Reference Manual, Rev. 1

Freescale Semiconductor

8-3

A debug interrupt occurs when no higher priority interrupt exists, a debug exception is indicated
in the DBSR, and debug interrupts are enabled (DBCR0[IDM] = MSR[DE] = 1). CSRR0, CSRR1,
MSR, and DBSR are updated as shown in

Table 8-2

.

Instruction execution resumes at address IVPR[32–47]

||

IVOR15[48–59] || 0b0000.

8.2.4

Deviations from the Book E Debug Model

The e500 core complex supports Book E debug mode with the following exceptions:

•

Instruction address compare registers 3 and 4 (IAC3, IAC4) and data address compare
registers 3 and 4 (DAC3, DAC4) along with their debug exceptions, are not implemented.

•

Only effective addresses are compared with instruction address compare (IAC1 or IAC2
debug events), and data address compare (DAC1 or DAC2 debug events).

•

Return debug events for the rfci instruction are not logged if MSR[DE] is cleared (debug
interrupts are disabled).

Table 8-2. Debug Interrupt Register Settings

Register

Setting

CSRR0 For debug exceptions that occur while debug interrupts are enabled (DBCR0[IDM] = 1 and MSR[DE] = 1), CSRR0 is

set as follows:
• For instruction address compare (IAC1 and IAC2 debug events), data address compare (DAC1R, DAC1W, DAC2R,

and DAC2W debug events), trap, or branch taken debug exceptions, set to the address of the instruction causing
the debug interrupt.

• For instruction complete debug exceptions, set to the address of the instruction that would have executed after the

one that caused the debug interrupt.

• For unconditional debug event (UDE) debug exceptions, set to the address of the instruction that would have

executed next if the debug interrupt had not occurred.

• For interrupt taken debug exceptions, set to the interrupt vector value of the interrupt that caused the interrupt taken

debug event.

• For return from interrupt (RET) debug exceptions, set to the address of the instruction that would have executed

after the

rfi

or

rfci

that caused the debug interrupt.

• For debug exceptions that occur while debug interrupts are disabled (DBCR0[IDM] = 0 or MSR[DE] = 0), a debug

interrupt occurs at the next synchronizing event if DBCR0[IDM] and MSR[DE] are modified such that they are both
set and if the debug exception status is still set in the DBSR. When this occurs, CSRR0 holds the address of the
instruction that would have executed next, not with the address of the instruction that modified DBCR0 or MSR and
thus caused the interrupt.

CSRR1 Set to the contents of the MSR at the time of the interrupt.

MSR

ME is unchanged. All other MSR bits are cleared.

DBSR

Set to indicate type of debug event (see

Chapter 8, “Debug Support

”).

«
...
317
318
319
320
321
...
»

Summary of Contents for PowerPC e500 Core





































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PowerPC e500 Core

Brand: Aaeon Pages: 132

Brand: Aaeon Pages: 50

Brand: Faytech Pages: 2

phyBOARD-Subra-i.MX6

Brand: Phytec Pages: 2

Pentium P5I430TX/IIB TITANIUM IIB

Brand: QDI Pages: 53

CVN X570 GAMING PRO V14

Brand: Colorful Pages: 64

Brand: Supermicro Pages: 90

Brand: Microchip Technology Pages: 52

MT9J003I12STCVH-GEVB

Brand: ON Semiconductor Pages: 5

Brand: Avalue Technology Pages: 75

Brand: Xilinx Pages: 88

K9N6PGM2-V2 - Motherboard - Micro ATX

Brand: MSI Pages: 153

Brand: JETWAY Pages: 47

BeagleBone Black Proto Cape

Brand: sparkfun Pages: 4

Brand: Gigabyte Pages: 39

Brand: Texas Instruments Pages: 33

Brand: Socket Pages: 37

Brand: DFI Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands