Data I/O UniSite-xpi User Manual Download Page 310 | Manualshive

Page: 310 / 413

background image

7. Messages

7-14

UniSite-xpi User Manual

I/O address beyond range of data format selected.

An I/O address in the data received exceeded the highest value allowed in the address field of the data
format selected. Prior to performing an upload or output to disk operation, the programmer calculates the
highest I/O address that will be output based on the parameters supplied by the user. The programmer
aborts the operation if the I/O address is too large for the data format selected. The formula for calculating
the highest I/O address is:

Highest I/O address = I/O addr User data size - 1

To avoid this error condition, either select a different data format (one which will support the I/O
addresses for the transfer operation), or decrease the value of the I/O offset address and/or the User data
size to achieve I/O addresses within the range of the present data format selected. The I/O addr offset
parameter is also considered an unsigned value if it is treated as a value of 0.

I/O timeout error. Press F3. Data checksum = ssssssss Xmit sum = ssssssss.

This error occurs when a file is being transferred from systems such as PC, Sun, or Vax over RS-232 or via
programmer disk drive. If the programmer displays data sum =

00000000

, no data was transferred. Other

hex values indicate the file transferred partially or completely. Check the following:

- Wrong Download Command Sent to Host: Your host machine will transfer a file receipt of the proper

command. Under HiTerm, the Download Host command must begin with “tr” or “transfer,” followed
by the appropriate drive letter, path, and filename.

- Wrong I/O Translation Format Selected: The format of the file being transferred must match the

description in the User Manual. If it doesn’t, enter the proper I/O translation format number and
transfer the file again.

- Unrecognized Characters in Beginning of File: The data file must begin with characters that match the

appropriate format described in the User Manual. Make sure the file has a “start character.”

- No Recognizable End-of-File Character: The data file must end with the proper end-of-file character or

record.

See page 7-50 for more information.

I/O timeout error. Data sum = sssssss.

This error occurs when a file is being transferred from systems such as PC, Sun, or Vax over RS-232 or via
programmer disk drive. If the programmer displays data sum =

00000000

, no data was transferred. Other

hex values indicate the file transferred partially or completely. Check the following:

- Wrong Download Command Sent to Host: Your host machine will transfer a file receipt of the proper

command. Under HiTerm, the Download Host command must begin with “tr” or “transfer,” followed
by the appropriate drive letter, path, and filename.

- Wrong I/O Translation Format Selected: The format of the file being transferred must match the

description in the User Manual. If it doesn’t, enter the proper I/O translation format number and
transfer the file again.

- Unrecognized Characters in Beginning of File: The data file must begin with characters that match the

appropriate format described in the User Manual. Make sure the file has a “start character.”

- No Recognizable End-of-File Character: The data file must end with the proper end-of-file character or

record.

See page 7-50 for more information.

«
...
308
309
310
311
312
...
»

Summary of Contents for UniSite-xpi






























































































































































































































































































































































































































Reviews:

No comments

Related manuals for UniSite-xpi

Brand: Acer Pages: 15

Brand: Acer Pages: 12

Brand: MSI Pages: 61

Brand: Portwell Pages: 7

Brand: J&W Pages: 28

Brand: BESTEK Pages: 52

TPS61090EVM-029

Brand: Texas Instruments Pages: 19

MBD-J-JNC9VL-H81

Brand: JETWAY Pages: 43

Brand: Norco Pages: 78

Brand: JETWAY Pages: 52

Brand: Renesas Pages: 17

Brand: Texas Instruments Pages: 36

Brand: TransCore Pages: 40

TPS5420EVM-175 SWIFT

Brand: Texas Instruments Pages: 16

SpacePC 1232 Series

Brand: Parvus Pages: 87

Brand: NXP Semiconductors Pages: 19

Brand: EPOX Pages: 55

Brand: Global Pages: 33

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands