Cisco NCS 2000 series Скачать руководство пользователя страница 403 | Manualshive

Страница: 403 / 602

background image

DETAILED STEPS

Clear the root-cause service-affecting alarm by using one of the following procedures, as appropriate:

•

Clear the LOS (OTS) Alarm, on page 277

procedure

•

Clear the LOS (TRUNK) Alarm, on page 279

procedure

•

Clear the LOS-P (OCH) Alarm, on page 284

procedure

•

Clear the LOS-P (AOTS, OMS, OTS) Alarm, on page 282

procedure

•

Clear the LOS-P (TRUNK) Alarm, on page 288

procedure

•

Clear the OPWR-LFAIL Alarm, on page 327

procedure

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

PORT-COMM-FAIL

Default Severity: Critical (CR), Service-Affecting (SA)

Logical Object: DWDM_CLIENT, DWDM_TRUNK

The port module communication failure (PORT-COMM-FAIL) alarm is raised on OTU2XP, GE_XP, GE_XPE,
10GE_XP, 10GE_XPE, 40G-MXP-C, 40E-MXP-C, 40ME-MXP-C, AR-MXP, and AR-XP line cards when
there is a pluggable port module (PPM) communication failure. The PPM communication failure is caused
due to physical damage or internal errors on the PPM.

Clear the PORT-COMM-FAIL Alarm

SUMMARY STEPS

1.

To Clear the PORT-COMM-FAIL alarm, perform the following:

DETAILED STEPS

To Clear the PORT-COMM-FAIL alarm, perform the following:

a) Soft reset the line card.
b) Delete PPM provisioning from the line card.

To delete PPM provisioning, see the "DLP-G727 Delete PPM Provisioning" task in the

Installing the GBIC, SFP,

SFP+, and XFP Optical Modules in Cisco ONS PlatformsInstalling the GBIC, SFP, SFP+, QSFP, XFP, CXP, CFP
and CPAK Optical Modules in Cisco NCS Platforms

document.

c) Re-provision the PPM on the line card.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

357

Alarm Troubleshooting

PORT-COMM-FAIL

«
...
401
402
403
404
405
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Express5800/E120d-M

Бренд: NEC Страницы: 2

Бренд: F5 Страницы: 72

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

RouterBOARD Groove

Бренд: MikroTik Страницы: 4

Бренд: Paradyne Страницы: 85

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

EdgeLens INT10G8LR56

Бренд: Garland Страницы: 30

LinkSmart KW6515

Бренд: Kasda Страницы: 31

FireWire 800 + Hi-Speed USB Combo

Бренд: SIIG Страницы: 20

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: FDI Страницы: 2

Бренд: ebm-papst Страницы: 13

Бренд: Pakedge Device & Software Страницы: 14

Бренд: MiWire Страницы: 24

Бренд: Rolls Страницы: 1

Бренд: ICP Страницы: 68

ADSL Ethernet & USB Combo Router Lynx L-510

Бренд: Starbridge Networks Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды