Cisco NCS 2000 series Скачать руководство пользователя страница 464

Страница: 464 / 602

Clear the TIM-S Alarm

SUMMARY STEPS

Double-click the DS3/EC1-48 card to open the card view.

Click the

Provisioning

EC1

Section Trace

tabs.

Choose the port from the

Port

pull-down.

In the Expected area, enter the correct string into the

Current Expected String

field.

Click

Apply

DETAILED STEPS

Step 1

Double-click the DS3/EC1-48 card to open the card view.

Step 2

Click the

Provisioning

EC1

Section Trace

tabs.

Step 3

Choose the port from the

Port

pull-down.

Step 4

In the Expected area, enter the correct string into the

Current Expected String

field.

Step 5

Click

Apply

If the alarm does not get cleared, you need to report a Service-Affecting (SA) problem. Log into the Technical Support
Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or log into

http://www.cisco.com/c/

en/us/support/web/tsd-cisco-worldwide-contacts.html

to obtain a directory of toll-free Technical Support numbers for

your country.

TRAF-AFFECT-RESET-REQUIRED

Default Severity: Minor (MN) and Non-Service affecting (NSA)

Logical Object: CARD

The Traffic Affecting Reset required alarm is raised when you have to reset the MR-MXP cards. This reset
impacts the traffic.

Clear the TRAF-AFFECT-RESET-REQUIRED Alarm

Step 1

Display the MR-MXP card in the card view.

Step 2

Click the

Provisioning > Card > Operating Modes

tabs.

Step 3

Click the

FGPA/FIRWAREUpgrade/TrafficAffectingReset

button.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

418

Alarm Troubleshooting

Clear the TIM-S Alarm

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды

Cisco NCS 2000 series, Руководство по устранению неисправностей

Результаты поиска

Содержание NCS 2000 series

Отзывы:

Похожие инструкции для NCS 2000 series

Бренды по названию

Популярные бренды