Cisco NCS 2000 series Скачать руководство пользователя страница 547 | Manualshive

Страница: 547 / 602

background image

Description

Error/Warning Message

Error/Warning
ID

Refer to the error message text.

One or more Osc terminations could not be created.

EID-3086

Refer to the error message text.

The OSC termination could not be edited.

EID-3087

No card of the specified type is
available to switch.

No {0} card is present to switch.

EID-3088

You cannot use or change the
specified state when the card is failed
or missing.

The {0} state cannot be used or changed when the {1}
has failed or is missing.

EID-3089

You cannot perform operation.

The operation cannot be performed because the {0} is
{1}LOCKED_ON/LOCKED_OUT.

EID-3090

Refer to the error message text.

The operation cannot be performed because the protect
card is active.

EID-3091

Select another service state and
proceed.

The requested action cannot be applied because the
service state is invalid.

EID-3092

Refer to the error message text.

The operation cannot be performed because the duplex
pair is {0}locked.

EID-3093

You cannot perform the requested
operation on the cross connect card
without having a backup cross connect
card.

The operation cannot be performed because no
cross-connect redundancy is available.

EID-3094

Refer to the error message text.

The deletion failed because the circuit is in use

EID-3095

Refer to the warning message text.

An internal communication error was encountered while
retrieving laser parameters. This can happen when
equipment is not present or when equipment is resetting.
Check the equipment state and try to refresh the values
again.

WID-3096

The ring termination you are trying to
access is in use. Try after sometime.

The ring termination is in use.

EID-3097

Select one of the ring terminations.

No ring terminations were selected.

EID-3098

Check the authentication key and
reenter.

The entered key does not match the existing
authentication key.

EID-3099

There was an error in authentication.
Verify that the key does not exceed
the character limit.

An error occurred during authentication.

EID-3100

The DCC metric should be in the
range of 1 to 65535.

The DCC metric must be between 1 and 65535.

EID-3101

There was an invalid DCC metric.

The DCC metric is invalid.

EID-3102

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

501

Error Messages

Error Messages Reference

«
...
545
546
547
548
549
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Aastra Страницы: 2

Бренд: Abocom Страницы: 11

Бренд: Abocom Страницы: 19

S5500-HI Switch Series

Бренд: H3C Страницы: 180

Бренд: H3C Страницы: 84

Бренд: H3C Страницы: 281

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 102

S12500CR Series

Бренд: H3C Страницы: 9

Бренд: H3C Страницы: 15

H3C S7500E Series

Бренд: H3C Страницы: 1565

Бренд: H3C Страницы: 4

InterReach Fusion ADCP-77-044

Бренд: TE Connectivity Страницы: 236

ILDA Gem Laser projector tool

Бренд: Stanwax Laser Страницы: 3

Бренд: NETGEAR Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды