Cisco NCS 2000 series Скачать руководство пользователя страница 307 | Manualshive

Страница: 307 / 602

background image

Clear the LOCAL-SUDI-CERT-VERIFICATION-FAILED Alarm

This alarm is cleared when the verification of an active SUDI certificate passes.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

LOCAL-CERT-EXPIRED

Default Severity: Major (MJ), Non-Service-Affecting (NSA)

Logical Object: EQPT

The Local Certificate Expired alarm is raised when the validity of an active certificate chain expires.

Clear the LOCAL-CERT-EXPIRED Alarm

Procure and install a the local active certificate chain.

If the condition does not clear, log into the Technical Support Website at

http://www.cisco.com/c/en/us/support/index.html

for more information or call Cisco TAC (1 800 553-2447).

LOCAL-FAULT

Default Severity: Major (MJ), Service-Affecting (SA)

Logical Objects: ETH

The LOCAL-FAULT alarm is raised on the GE_XP, GE_XPE, 10GE_XP, and 10GE_XPE card ports
provisioned in 10 GE LAN PHY mode under the following conditions:

• when there is a loss of signal on the port.

• when a local fault character sequence is received in the incoming MAC stream as defined in IEEE 802.3ae,

10 GE fault signaling scheme.

The LOCAL-FAULT alarm is raised on the 40G-MXP-C, 40E-MXP-C, and 40ME-MXP-C card client ports
provisioned with 10 GE or 10 GE FC payloads when a local fault character sequence is received in the incoming
MAC stream as defined in IEEE 802.3ae, 10 Gigabit Ethernet fault signaling scheme.

Cisco NCS 2000 series Troubleshooting Guide, Release 11.0

261

Alarm Troubleshooting

Clear the LOCAL-SUDI-CERT-VERIFICATION-FAILED Alarm

«
...
305
306
307
308
309
...
»

Содержание NCS 2000 series



























































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 2000 series

Бренд: Panasonic Страницы: 44

Бренд: Octavo Страницы: 28

Бренд: Obihai Страницы: 2

Бренд: Garland Страницы: 6

Бренд: Stanwax Laser Страницы: 9

Compact Emulator M30620T-CPE

Бренд: Renesas Страницы: 52

Бренд: EnGenius Страницы: 3

Бренд: ESD Страницы: 28

IPAM-1600s Series

Бренд: C-Com Страницы: 148

NetIron MLXe Series

Бренд: Brocade Communications Systems Страницы: 305

Бренд: Supero Страницы: 16

Бренд: ZyXEL Communications Страницы: 66

Бренд: Navitar Страницы: 1

Бренд: ZyXEL Communications Страницы: 2

Smartio CP-104UL

Бренд: Moxa Technologies Страницы: 2

AMSTX-CF Series

Бренд: ADLINK Technology Страницы: 73

Бренд: Radio Shack Страницы: 154

32 bit 10/100 Fast Ethernet Card A02-S32-S

Бренд: Atlantis Land Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды